SELVA MARINE Kingfish 25 Service Manual page 390

Installing the propeller shaft
housing assembly ......................... 8-19
Installing the PTT motor............................9-65
Installing the PTT unit ...............................9-59
Installing the remote control box and
tachometer (remote control model).........3-15
Installing the shift cable and
throttle cable (remote control model) ......3-13
Installing the shift rod,
oil seal housing, and drive shaft.... 8-19
Installing the sprocket and timing belt.......7-24
Installing the starter motor ........................5-27
Installing the steering arm............... 9-42
Installing the thermo sensor......................7-52
Installing the throttle link,
throttle cam, and shift cam............ 6-16
Installing the upper case ........9-17
Installing the water pump ................ 8-20
Installing the wiring harness......................7-30
Installing the wiring harness
(remote control model)............................3-15
Intake and exhaust system .......................2-12
Intake silencer.............................................6-9
L.
Lower unit ..................................1-5
Lower unit (high thrust model) ..................8-32
Lower unit assembly .................................1-19
Lower unit technical data ..........................1-19
Lubricant, sealant,
and thread locking agent...........................0-6
Lubricating the outboard motor ...............10-14
Lubrication system ....................................2-10
M.
Maintenance interval chart........................10-1
Manual format .............................................0-4
Manual starter ................................... 1-14
Measuring the forward
and reverse gear backlash......................8-28
Measuring the forward and reverse
gear backlash before disassembly..........8-55
Measuring the forward gear backlash.......8-63
Measuring the peak voltage......................5-10
Measuring the reverse gear backlash.......8-66
Measuring the starter rope........................7-11
Model data ..................................................1-3
Model designation.......................................1-2
Model features ............................................1-1
Mounting the outboard motor....................3-11
Mounting the rigging grommet ..................3-13
N.
,
8-48
Non-reusable part....................................... 0-3
O.
Oil pan and exhaust manifold ................... 9-32
Oil pan and exhaust manifold
Operation during malfunctions.................. 2-18
Outboard motor installation ........................ 3-1
,
8-47
Outline ............................. 2-1
P.
,
9-44
Part, lubricant, and sealant......................... 0-2
Performance ............................................... 1-3
,
6-19
Pinion shim (T3) selection table ............... 8-61
, ,
9-20 9-24
Port view..................................................... 5-1
,
8-49
Power unit........................ 1-4
Power unit (check and adjustment) ............ 7-1
Power unit assembly ................................ 7-12
Power unit technical data ......................... 1-13
Predelivery check ..................................... 10-3
Prime Start system ................................... 2-13
Propeller ..................................................... 0-1
Propeller selection .................................... 3-16
Propeller shaft housing............................... 8-7
, ,
1-22 8-1
Propeller shaft housing
Propeller size............................................ 3-16
PTT cylinder ............................................. 9-73
PTT electrical system ............................... 5-29
PTT gear pump......................................... 9-66
PTT motor................................................. 9-61
PTT requirement......................................... 1-7
PTT system .............................................. 1-20
PTT unit ................................. 1-23
R.
,
7-5
Refacing the valve seat ............................ 7-43
Removing the carburetor .......................... 6-12
Removing the clamp bracket ...........9-48
Removing the cylinder head ..................... 7-35
Removing the drive shaft,
Removing the exhaust cover .................... 7-51
Removing the flywheel magnet ................ 7-23
Removing the lower unit ....................8-3
Removing the manual starter ..................... 7-7
Removing the oil filter ............................... 7-51
Removing the oil pressure switch ............. 7-51
Removing the oil seal housing,
(high thrust model).................................. 9-36
(high thrust model).................................. 8-38
oil seal housing, and shift rod ................. 8-14
drive shaft, and shift rod ......................... 8-44
Index
, , ,
2-8 2-15 10-1
, , ,
1-13 1-21 2-8
, ,
2-15 9-58
,
9-56
,
8-34
i-4