Delta VFD300C43S-HS User Manual page 318

Chapter 12 Description of Parameter SettingsC2000-HS
 When using the crane application and MOx = 42, Pr. 02-34 must be larger than Pr. 02-58; Pr.
02-33 must be larger than Pr. 02-57.
 Add Remote IO function to directly control drive's AO / DO and read current AI / DI status
through the standard MODBUS, the corresponding indexes of 26xx are as following:
bit15 bit14
2600h MI15 MI14
2640h - -
2660h AVI
2661h ACI
2662h AUI
266Ah AI10
266Bh AI11
26A0h AFM1
26A1h AFM2
26AAh AO10
26ABh AO11
In addition, the AI and DI value can be read directly, while DO and AO must be controlled by
MODBUS under corresponding parameter function. The related parameter definition is as
following:
DO:
Terminal
RY1
RY2
MO1
MO2
MO10
MO11
MO12
MO13
MO14
MO15
AO:
Terminal
AFM1
AFM2
AFM10
AFM11
Multi-function Output Direction

Settings 0000h–FFFFh (0: N.O.; 1: N.C.)
 This parameter is in hexadecimal.
 This parameter is set by a bit. If the bit is 1, the corresponding multi-function output acts in an
opposite way.
Example: Assume Pr.02-13 = 1 (indication when the drive is operating). If the output is positive,
the bit is set to 0, and then Relay is ON when the drive runs and is OFF when the drive stops. On
the contrary, if the output is negative, and the bit is set to 1, then the Relay is OFF when the drive
runs and is ON when the drive stops.
bit15 bit14
MO20 MO19
bit13 bit12 bit11 bit10
MI13 MI12 MI11 MI10
MO15
- - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - -
- - -
- - -
- - -
Pr. Setting
Pr. 02-13 = 51
Pr. 02-14 = 51
Pr. 02-16 = 51
Pr. 02-17 = 51
Pr. 02-36 = 51
Pr. 02-37 = 51
Pr. 02-38 = 51
Pr. 02-39 = 51
Pr. 02-40 = 51
Pr. 02-41 = 51
Pr. Setting
Pr. 03-20=21
Pr. 03-23=21
Pr. 14-12=21
Pr. 14-13=21
bit13 bit12 bit11 bit10
MO18 MO17 MO16 MO15 MO14 MO13 MO12 MO11 MO10 MO2 MO1 Reserved RY2 RY1
bit6
bit9 bit8 bit7
MI8 MI7 MI6 MI5
MO11
MO14 MO13 MO12
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
Indexes of MODBUS direct control
The bit0 at 2640h
The bit1 at 2640h
The bit3 at 2640h
The bit4 at 2640h
The bit5 at 2640h
The bit6 at 2640h
The bit7 at 2640h
The bit8 at 2640h
The bit9 at 2640h
The bit10 at 2640h
Indexes of MODBUS direct control
The value at 26A0h
The value at 26A1h
The value at 26AAh
The value at 26ABh
bit9 bit8 bit7
12.1-02-20
bit5 bit4 bit3 bit2
MI4 MI3 MI2 MI1
MO10 MO2 MO1
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
Default: 0000h
bit6 bit5 bit4 bit3
bit1 bit0
REV FWD
- RY2 RY1
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
bit2 bit1 bit0