Xerox WorkCentre 5790 Series Service Manual page 641

Table 6 07-5XX Status codes
Status
Code UI Message Reason for Message
07-517 Inserter empty, please Paper sensor detects no paper Reload paper.
reload
07-521 Remove misfed sheet. IOT microprocessor detects
Close tray 1 Tray 1 open
07-522 Remove misfed sheet. IOT microprocessor detects
Close tray 2 Tray 2 open
07-523 Remove misfed sheet. IOT microprocessor detects
Close tray 3 Tray 3 open
07-524 Remove misfed sheet. IOT microprocessor detects
Close tray 4 Tray 4 open
07-526 Close tray 5 door Tray 5 door has been detected
open
07-531 Tray 1 is low on paper Tray 1 paper low
07-532 Tray 2 is low on paper Tray 2 paper low
07-533 Tray 3 is low on paper Tray 3 paper low
07-534 Tray 4 is low on paper Tray 4 paper low
07-536 Tray 5 is low on paper Tray 5 paper below 5% full
07-539 Tray 5 is overloaded, Paper equals or is more than
please remove excess 100% full in tray 5
paper
07-541 Tray 1 is out of service, Tray 1 out of service.
please use a different tray
07-542 Tray 2 is out of service, Tray 2 out of service.
please use a different tray
07-543 Tray 3 is out of service, Tray 3 elevate top sensor does
please use a different tray not turn on within 7 seconds
after elevator motor on.
07-544 Tray 4 is out of service, Tray 4 elevate top sensor does
please use a different tray not turn on within 7 seconds
after elevator motor on
07-546 Tray 5 is out of service, Tray 5 cannot feed paper
please use a different tray
Xerox® WorkCentre® 5790 Family
Status
Reference / Action Code UI Message
07-550 Tray 3 is lifting
07-551 Tray 1 is lifting
Close tray. Perform 07-
07-552 Tray 2 is lifting
301 RAP
07-560 Tray 4 is lifting
07-561 Tray 5 is lifting, please
Close tray. Perform 07-
wait
302 RAP
07-562 -
Close Tray. Perform 07-
07-563 Tray 5 is unavailable.
303 RAP
Check for obstructions in
Close Tray. Perform 07-
Tray 5
304 RAP
07-564 Tray 5 is unavailable.
Close the door, or per-
Check for obstructions in
form 07-306
Tray 5
Perform 07A RAP
07-571 Paper size mismatch.
Perform 07A RAP
Check paper in Tray 1.
IOT microprocessor Some image loss may
detects Tray 3 paper occur
level at 25%. Perform
07-572 Paper size mismatch.
07B RAP
Check paper in Tray 2.
Some image loss may
IOT microprocessor
detects Tray 4 paper occur
level at 25%. Perform
07-573 Paper size mismatch.
07B RAP
Check paper in Tray 3.
Add paper. If neces- Some image loss may
sary, perform 07-373 occur
and 07-374 RAPs
Remove some paper. If
necessary, perform 07- 07-574 Paper size mismatch.
373 and 07-374 Check paper in Tray 4.
Some image loss may
Perform 07H RAP
occur
Perform 07H RAP
07-575 Paper size mismatch.
Perform 07-355 RAP
Check paper in Bypass
tray. Some image loss
may occur
Perform 07-360 RAP
07-576 Paper size mismatch.
Check paper in tray 5
Switch the machine off
07-580 Re-order but do not
and on, GP 14. Check
replace the Tray 5 Feed
that the tray is in the
Rolls
correct position. Per-
07-581 Slide Tray 5 up to
form 07-306, 07-372, or
machine
07-373 RAP
May 2013
2-609
Table 6 07-5XX Status codes
Reason for Message Reference / Action
Tray 3 is lifting. Perform
Tray 1 is lifting. Perform
Tray 2 is lifting. Perform
Tray 4 is lifting Perform
Tray 5 is currently lifting Perform
Tray 5 is currently lowering Perform
Tray 5 lifting has stopped Perform
Tray 5 lowering has stopped Perform
First sheet fed after a tray 1 Check the paper in tray
status change does not match 1. Perform
the confirmed stock
First sheet fed after a tray 2 Check the paper in tray
status change does not match 2. Perform
the confirmed stock
First sheet fed after a tray 3 Check the paper in tray
status change does not match 3. Check that the tray is
the confirmed stock set to correct paper
size, (W/O
ADJ 7.1 or
151)
First sheet fed after a tray 4 Check the paper in tray
status change does not match 4. Check that the tray is
the confirmed stock set to correct paper
size, (W/O
ADJ 7.1 or
151)
First sheet fed after a bypass Check the paper in
tray status change does not bypass tray and the
match the confirmed stock side guide is set cor-
rectly
The first sheet after a tray 5 Confirm the paper size
status change does not match in the UI
the confirmed stock
Near the end of life - ensure Order new feed roll kit,
new stock is available PL 8.45 Item 2
Tray 5 is un-docked Perform
Status Indicator RAPs
07-355 RAP
07-353 RAP
07-354 RAP
07-360 RAP
07-373
07-374
07-373
07-374
07E RAP
07E RAP
TAG 151)
(W/TAG
ADJ 7.5
TAG 151)
(W/TAG
ADJ 7.5
07-372
OF4a