Table of Contents
Advertisement
11C-110 2K LCSS Initialization Failure RAP
When an initialization command is received from the machine, the units are initialized in two
stages:
•
The following units are initialized sequentially:
1.
If the staple head is not at the home position, it is driven to the home position
2.
If the stapling unit is not at the home position, it is driven to the home position
3.
If the ejector is not at the home position, it is driven to the home position
•
The following units are then initialized simultaneously:
1.
If the front tamper is not at the home position, it is driven to the home position
2.
If the rear tamper is not at the home position, it is driven to the home position
3.
If the hole punch is not at the home position, it is driven to the home position
4.
If the paddle is not at the home position, it is driven to the home position
5.
If the stacker is not at the home position, it is driven to the home position
NOTE: The staple cartridge must be fully pushed home.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP
14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Check the fuse on the 2K LCSS PWB, If the fuse is good, continue at the procedure. If the fuse
not good, install a new 2K LCSS PWB,
PL 11.26 Item
Check the 2K LCSS PWB DIP switch settings, refer to
tings RAP.
Remove the 2K LCSS covers,
REP
11.1-110, so that the units can be viewed. Cheat the front
door interlock switch and the top cover interlock switch. Check that LED 2 is illuminated, this
shows that all interlocks are made. If the LED fails to illuminate, go to
11-303-110
Interlocks RAP.
Procedure
Refer to
Figure
1. Check that the software heartbeat is present on LED 1. The LED should
flash twice per second if the 2K LCSS software is running. If necessary, re-load the 2K LCSS
software, refer to
GP 4
Machine Software.
If the initialization sequence fails to place any unit at the home position, refer to the appropriate
RAPs:
•
Front tamper not at home, refer to
Tamper Move Failure RAP
•
Rear tamper not at home, refer to
319-110
Rear Tamper Move Failure RAP.
•
Paddle not at home, refer to
11-024-110, 11-025-110
•
Bin 1 not at home, refer to
11-030-110, 11-334-110, 11-335-110, 11-336-110
ment Failures RAP.
•
Punch not at home, refer to
11-043-110, 11-350-110
Status Indicator RAPs
11C-110
WARNING
1.
11F-110
2K LCSS PWB DIP Switch Set-
11-300-110, 11-302-110,
11-005-110, 11-006-110, 11-310-110, 11-311-110
11-007-110, 11-008-110, 11-312-110, 11-313-110, 11-
Paddle Roll Failure RAP.
Hole Punch Operation Failure RAP
•
Staple head not at home, refer to
RAP.
•
Stapling unit not at home, refer to
Failure RAP.
•
Ejector not at home, refer to
RAP.
Front
Bin 1 Move-
May 2013
2-350
11-050-110, 11-360-110
Staple Head Operation Failure
11-053-110, 11-370-110
Staple Head Unit Movement
11-320-110, 11-322-110
Compiler Ejector Movement Failure
LED 2
Figure 1 LED location
Xerox® WorkCentre® 5790 Family
Fuse
LED 1
Advertisement
Chapters
Table of Contents
