Subaru Impreza 2003 Service Manual page 2058

MANUAL TRANSMISSION AND DIFFERENTIAL
26.Clutch Housing
A: REMOVAL
1) Remove the manual transmission assembly
from vehicle. <Ref. to 6MT-37, REMOVAL, Manual
Transmission Assembly.>
2) Prepare the transmission for overhaul. <Ref. to
6MT-42, Preparation for Overhaul.>
3) Remove the oil pipe, neutral position switch,
back-up light switch and harness. <Ref. to 6MT-44,
REMOVAL, Oil Pipe.>, <Ref. to 6MT-47, REMOV-
AL, Neutral Position Switch.>, <Ref. to 6MT-45,
REMOVAL, Back-up Light Switch.>
4) Remove the extension case. <Ref. to 6MT-49,
REMOVAL, Extension Case.>
5) Remove the transfer driven gear. <Ref. to 6MT-
60, REMOVAL, Transfer Driven Gear.>
6) Remove the center differential. <Ref. to 6MT-62,
REMOVAL, Center Differential.>
7) Remove the oil pump. <Ref. to 6MT-63, RE-
MOVAL, Oil Pump.>
8) Remove the transmission case. <Ref. to 6MT-
67, REMOVAL, Transmission Case.>
9) Remove each gear assembly. <Ref. to 6MT-72,
REMOVAL, Main Shaft Assembly.>
10) Remove the drive pinion shaft assembly. <Ref.
to 6MT-99, REMOVAL, Drive Pinion Shaft Assem-
bly.>
11) Remove the front differential assembly. <Ref.
to 6MT-105, REMOVAL, Front Differential Assem-
bly.>
12) Remove the vehicle speed sensor. <Ref. to
6MT-34, REMOVAL, Vehicle Speed Sensor.>
13) Remove the speedometer gear. <Ref. to 6MT-
113, REMOVAL, Speedometer Gear.>
B: INSTALLATION
1) Install the pitching stopper bracket.
Tightening torque:
41 N·m (4.2 kgf-m, 30.2 ft-lb)
2) Install the speedometer gear. <Ref. to 6MT-113,
INSTALLATION, Speedometer Gear.>
3) Install the vehicle speed sensor. <Ref. to 6MT-
34, INSTALLATION, Vehicle Speed Sensor.>
4) Install the front differential assembly. <Ref. to
6MT-106, INSTALLATION, Front Differential As-
sembly.>
5) Install the drive pinion shaft assembly. <Ref. to
6MT-99, INSTALLATION, Drive Pinion Shaft As-
sembly.>
6) Install each gear assembly at once. <Ref. to
6MT-73, INSTALLATION, Main Shaft Assembly.>
7) Install the transmission case. <Ref. to 6MT-68,
INSTALLATION, Transmission Case.>
8) Install the oil pump. <Ref. to 6MT-64, INSTAL-
LATION, Oil Pump.>
CLUTCH HOUSING
9) Install the center differential. <Ref. to 6MT-62,
INSTALLATION, Center Differential.>
10) Install the transfer driven gear. <Ref. to 6MT-
60, INSTALLATION, Transfer Driven Gear.>
11) Install the extension case. <Ref. to 6MT-49, IN-
STALLATION, Extension Case.>
12) Install the oil pipe, neutral position switch,
back-up light switch and harness. <Ref. to 6MT-44,
INSTALLATION, Oil Pipe.>, <Ref. to 6MT-47, IN-
STALLATION, Neutral Position Switch.>, <Ref. to
6MT-45, INSTALLATION, Back-up Light Switch.>
13) Install the manual transmission assembly to ve-
hicle. <Ref. to 6MT-39, INSTALLATION, Manual
Transmission Assembly.>
C: DISASSEMBLY
1) Remove the clutch release bearing guide.
2) Remove the oil seal.
ST 398527700
NOTE:
Do not reuse the oil seal.
6MT-128
PULLER ASSY
ST
MT-00717
MT-00718