Subaru Impreza 2003 Service Manual page 2435

DIAGNOSTICS PROCEDURE WITHOUT DIAGNOSTIC TROUBLE CODE (DTC)
Step
2 CHECK SPECIFICATIONS OF ABSCM&H/U.
Check the specifications of mark on
ABSCM&H/U.
CK: FWD AT
CL: FWD MT
CU: AWD AT
CV: AWD MT
CX: AWD MT (STi model)
CY: AWD MT (STi with Driver's control
center differential model)
3 CHECK INPUT VOLTAGE OF LATERAL G
SENSOR.
1)Turn the ignition switch to OFF.
2)Remove the console box.
3)Remove the lateral G sensor from vehicle.
(Do not disconnect the connector.)
4)Turn the ignition switch to ON.
5)Measure the voltage between lateral G sen-
sor connector terminals.
Connector & terminal
(B257) No. 1 (+) — No. 3 ( − − − − ):
4 CHECK OPEN CIRCUIT IN LATERAL G SEN-
SOR OUTPUT HARNESS AND GROUND
HARNESS.
1)Turn the ignition switch to OFF.
2)Disconnect the connector from ABSCM&
H/U.
3)Measure the resistance between
ABSCM&H/U connector terminals.
Connector & terminal
LHD:(B301) No. 29 — No. 28:
RHD: (F49) No. 29 — No. 28:
5 CHECK GROUND SHORT IN LATERAL G
SENSOR OUTPUT HARNESS.
1)Disconnect the connector from lateral G sen-
sor.
2)Measure the resistance between
ABSCM&H/U connector and chassis ground.
Connector & terminal
LHD: (B301) No. 29 — Chassis ground:
RHD: (F49) No. 29 — Chassis ground:
6 CHECK BATTERY SHORT OF HARNESS.
Measure the voltage between ABSCM&H/U
connector and chassis ground.
Connector & terminal
LHD: (B301) No. 29 (+) — Chassis
ground ( − − − − ):
RHD: (F49) No. 29 (+) — Chassis ground
( − − − − ):
7 CHECK BATTERY SHORT OF HARNESS.
1)Turn the ignition switch to ON.
2)Measure the voltage between ABSCM&H/U
connector and chassis ground.
Connector & terminal
LHD: (B301) No. 29 (+) — Chassis
ground ( − − − − ):
RHD: (F49) No. 29 (+) — Chassis ground
( − − − − ):
Check
Does the vehicle specification
and ABSCM&H/U specifica-
tion match?
Is the voltage 4.75 — 5.25 V? Go to step 4.
Is the resistance 5.0 — 5.6
kΩ?
Is the resistance more than 1
MΩ?
Is the voltage less than 1 V?
Is the voltage less than 1 V?
ABS-95
ABS (DIAGNOSTICS)
Yes
Go to step 3. Replace the
ABSCM&H/U.
<Ref. to ABS-7,
ABS Control Mod-
ule and Hydraulic
Control Unit
(ABSCM&H/U).>
Repair the har-
ness/connector
between lateral G
sensor and
ABSCM&H/U.
Go to step 5. Repair the har-
ness/connector
between lateral G
sensor and
ABSCM&H/U.
Go to step 6. Repair the har-
ness between lat-
eral G sensor and
ABSCM&H/U.
Go to step 7. Repair the har-
ness between lat-
eral G sensor and
ABSCM&H/U.
Go to step 8. Repair the har-
ness between lat-
eral G sensor and
ABSCM&H/U.
No