FujiFilm PROFECT CS Service Manual page 492

6. Feed/Load Conveyor 6.
Unit 6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.8.1 Removal Procedures
6.8.2 Reinstallation Procedures
6.9
6.9.1 Removal Procedures
6.9.2 Reinstallation Procedures
6.10
6.10.1 Removal Procedures
6.10.2 Reinstallation Procedures
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
6.23
6.23.1 Removal Procedures
6.23.2 Reinstallation Procedures
6.24
6.24.1 Removal Procedures
6.24.2 Reinstallation Procedures
6.25
6.25.1 Removal Procedures
6.25.2 Reinstallation Procedures
6.26
6.27
6.27.1 Removal Procedures
6.27.2 Reinstallation Procedures
011-202-08E
09.30.2009 FM5540
Feed/Load Conveyor Unit
Feed/Load Conveyor Unit
IP Feed/Load Sensors (SB1, 2, 3, 4)
Path Changeover Shelf Sensors (SB7, 8, 9)
Convergence Path Changeover Sensor (SB10) MC-91
Path Changeover HP Sensor (SB11)
IP Jam Handling Assembly
Brush Roller Assembly
Cam Bracket Assembly (Upper Reference Side) MC-94
Path Changeover Mechanism
Cam Bracket Assembly (Lower Reference Side) MC-100
Gears Bracing Bracket
(Upper Opposite-Reference Side)
Gears Bracing Bracket
(Lower Opposite-Reference Side)
Conveyance Mechanism
(Opposite-Reference Side Gears)
Pre-BCR IP Sensor (SB5)
Pre-Convergence IP Sensor (SB6)
IP Transport Motor (MB1)
Convergence Unit IP Transport Motor (MB2)
Convergence Path Changeover Guide
Driving Motor (MB3)
Shock-Absorbing Roller Assemblies
(for the First, Second, and Third Shelves)
Shock-Absorbing Roller Assembly
(for the Fourth Shelf)
Antistatic Members
Shock-Absorbing Rollers (Convergence Unit)
Rubber Rollers (A, B, C, D, E, F, G, and H)
Arm and Bearing (for the First Shelf)
Arms and Bearings (for the Second,
Third, and Fourth Shelves)
Path Changeover Guides (for the First,
Second, Third, and Fourth Shelves)
Guides (for the First, Second, Third, and
Fourth Shelves)
MC-88
MC-88
MC-90
MC-90
MC-91
MC-92
MC-92
MC-94
MC-95
MC-96
7. Side-Positioning
MC-96
Conveyor Unit
MC-97
MC-100
MC-102
MC-104
MC-104
MC-105
MC-106
MC-106
MC-107
MC-108
MC-109
MC-110
MC-110
MC-111
MC-111
MC-112
MC-112
MC-114
MC-118
MC-118
MC-119
MC-120
MC-120
MC-121
MC-123
MC-124
MC-124
MC-125
6.28 Guide (Convergence Unit Lower Side)
6.29 Rubber Rollers (I, J, K, and L)
6.30 Rubber Rollers (M and N)
6.31 Rubber Rollers (O and P)
6.32 Rubber Rollers (Q and R)
6.33 Convergence Path Changeover Guide
6.34 Rubber Rollers (S and T)
6.35 Guide (Convergence Unit Upper Side)
6.36 Half-Clutch Spur Gear (Upper Reference Side) MC-139
6.36.1 Removal Procedures
6.36.2 Reinstallation Procedures
7. Side-Positioning Conveyor Unit
7.1 Side-Positioning Conveyor Unit
7.1.1 Removal Procedures
7.1.2 Reinstallation Procedures
7.2 Side-Positioning Mechanism HP Sensor (SC1) MC-149
7.3 Spur Gears (Reference Side)
7.4 Grip Release HP Sensor (SC2)
7.5 Side-Positioning IP Sensor (SC3)
7.6 Cleaning Guide HP Sensor (SC4)
7.7 Timing Belt
7.8 Side-Positioning Motor (MC1)
7.9 Grip Release Motor (MC2)
7.10 IP Transport Motor (MC3)
7.11 Cleaning Guide Driving Motor (MC4)
7.12 Latch Drive Unit (Overall)
7.13 Latch Assembly (Latch Driver)
7.14 Latch Assembly (Reference Side)
7.15 Tensioner
7.16 Planetary Gear Assembly
7.17 Spur Gear (Opposite Reference Side)
7.18 Antistatic Members
7.19 Grip Mechanism (Reference Side)
7.20 Grip Mechanism (Opposite Reference Side)
7.21 Grip Shaft
7.22 Shock-Absorbing Roller Assembly
7.23 Rubber Roller (A)
7.24 Rubber Roller (B)
7.25 Rubber Rollers (C and D)
7.26 Rubber Roller (E)
7.27 Rubber Roller (F)
7.28 Guide
7.29 Cleaning Guide Assembly
7.30 Cleaning Guide
7.31 Tape
7.31.1 Removal Procedures
7.31.2 Reinstallation Procedures
CR-IR 363 Service Manual
MC-3
MC-127
MC-128
MC-129
MC-131
MC-132
MC-134
MC-136
MC-137
MC-139
MC-140
MC-142
MC-142
MC-142
MC-145
MC-149
MC-150
MC-151
MC-151
MC-152
MC-153
MC-154
MC-155
MC-156
MC-157
MC-159
MC-160
MC-161
MC-161
MC-162
MC-162
MC-163
MC-164
MC-165
MC-165
MC-166
MC-167
MC-168
MC-170
MC-173
MC-176
MC-177
MC-179
MC-181
MC-181
MC-184
MC-3