FujiFilm PROFECT CS Service Manual page 19

Contents Troubleshooting (MT)
15.4 Countermeasure against Image Abnormalities Due
to Laser Light Blocked under a Low Temperature ................ MT-254
15.5 Countermeasure against Image Abnormality
of White-Black-White ............................................................ MT-254
15.6 Countermeasure against Image Abnormalities like
Annual Rings ........................................................................ MT-255
16. Removing the IP ............................................................MT-256
16.1 Removing the IP from the Feed/Load Conveyor Unit ........... MT-256
16.1.1 When the IP is Jammed in the Cassette Set Unit .............................MT-256
16.1.2 When the IP is Jammed in the Side-Positioning Conveyor Unit .......MT-257
16.2 Removing the IP from the Erasure Conveyor Unit ............... MT-259
16.2.1 When the IP is Jammed in the Subscanning Unit
or Post-Reading Conveyor Unit ........................................................MT-259
16.2.2 When the IP is Jammed in the Erasure Conveyor Unit .....................MT-261
17. Block Diagrams .............................................................MT-263
17.1 BCRA1, BCRA2, LED17A .................................................... MT-263
17.2 BCRA3, BCRA4, BCRC1, LED17A ...................................... MT-263
17.3 LCD17A, LDD12A, SYN12A, POL17A ................................. MT-264
17.4 Sensors (SA1 to SA12) ........................................................ MT-265
17.5 Sensors (SA13 to SA24) ...................................................... MT-266
17.6 Sensors (SC1 to SC4, SG1 to SG2, SD1 to SD2,
SE1 to SE2, SE4 to SE5) ..................................................... MT-267
17.7 Sensors (SB1 to SB11) ........................................................ MT-268
17.8 Sensors (SZ1 to SZ5) and FFM Motor (MZ1) ...................... MT-269
17.9 Motors
(MA1 to MA4, MD1 to MD2, ME1, ME3, MZ2 to MZ3) ......... MT-270
011-202-07
09.30.2008 FM5340
17.10 Motors (MB1 to MB3, MC1 to MC4, ME2, MZ4) .................. MT-271
17.11 Actuators (SOLA1 to SOLA4, PA1 to PA4,
SVA1 to SVA4, CLA1 to CLA4) ............................................ MT-272
17.12 Actuator (SOLE1) ................................................................. MT-273
17.13 Erasure Lamps and Fan 1 .................................................... MT-274
17.14 Erasure Lamps and Fan 2 .................................................... MT-275
18. Board Test in MUTL ......................................................MT-276
18.1 Analysis Flow ....................................................................... MT-276
18.2 Board Test ............................................................................ MT-277
18.2.1 All Board ............................................................................................MT-278
18.2.2 CPU Board ........................................................................................MT-279
18.2.3 IMG Board .........................................................................................MT-280
18.2.4 SCN/SCT Board ................................................................................MT-281
18.2.5 SNS/DRV Board ................................................................................MT-282
18.2.6 INV Board ..........................................................................................MT-283
19. Gathering Various Data When Trouble Occurs ..........MT-284
20. Troubleshooting Failures where Error Code
Is Undetectable and Machine does not Boot Up ........MT-285
20.1 Analysis Flow for Bootup Failure .......................................... MT-285
20.2 Checking the LEDs on the IMG Board and CPU Board ....... MT-286
20.3 Checking the DIP SW Setting on the CPU91A Board .......... MT-287
20.3.1 Checking the DIP SW Setting of the CR-IR 363 ...............................MT-287
20.4 Procedures for Restoring the RU Application ....................... MT-288
20.4.1 Procedures for Restoring the RU Application....................................MT-288
20.4.2 Touch Panel Calibration Procedures .................................................MT-296
CR-IR 363 Service Manual
0.13
0.13