Radwin 5000 HPMP User Manual page 497

MIB Traps
Table C‐4: MIB Traps (Sheet 7 of 8)
Name
hssSyncToProperSourceAchievedClear
hssSyncPulseDisappearedClear
tdmBackupClear
linkLockAuthorizedRemoteODU
linkLockAuthorizedODU
linkAuthenticationDisabled
hotStandbyClear
sfpExtraction
sfpPort1Clear
compatibleIdus
desiredRatioCanNotBeAppliedClear
cbwMatch
switchCbwAndChannel
ringRplStateIdle
ringEthServiceStatus
ringFirstRpmReceived
ringEthernetSrviceUnblockedTO
gpsSynchronized
hbsEncryptionClear
hbsEhServiceOpenedToHsu
hbsSynchronizedHsuAlarm
hbsActiveHbs
switchCBW
changeRatio
RADWIN 5000 HPMP User Manual
ID Severity Description
219 normal Indicates that synchronization to a proper Sync source
was achieved. Contains a single parameter which is its
description: 1 ‐ Description: HSS sync pulse ‐ Up.
220 normal Indicates that HSS additional sync pulse disappeared.
Contains a single parameter which is its description: 1 ‐
Description: HSS additional sync pulse was disappeared.
221 normal Indicates that the TDM main link was activated.
Contains a single parameter which is its description: 1 ‐
Description: TDM main link was activated.
222 normal Indicates that the remote ODU is authorized. Contains
a single parameter which is its description: 1 ‐
Description: Authorized remote ODU connection
accepted.
223 normal Indicates that the ODU is authorized. Contains a single
parameter which is its description: 1 ‐ Description:
Authorized ODU connection permitted.
224 normal Indicates that the Link Lock is disabled. Contains a
single parameter which is its description: 1 ‐
Description: Link Authentication has been disabled.
225 normal Indicates that the Primary Link Was Activated. Contains
a single parameter which is its description: 1 ‐
Description: Primary Link Is Active.
226 normal Indicates that a device was extracted from SFP Port
227 normal Indicates the SFP port 1 status changed to connected.
Contains two parameters: 1 ‐ Description: SFP port 1
status changed to connected ‐ %s 2 ‐ %s Is the Eth.
mode (speed & duplex)
228 normal Indicates that the ODU has identified compatible Idus
on both sides of the link.
229 normal Indicates Current UL/DL Ratio Is Equal To Desired Ratio.
230 normal Indicates that a Channel Bandwidth match was
detected. Contains a single parameter which is its
description: 1 ‐ Channel Bandwidth value in MHz.
231 normal Indicates that the system is switching Channel
Bandwidth and channel frequency. Contains two
parameters: 1 ‐ Switching to Channel Bandwith %n0
MHz and to channel %n1 GHz.
232 normal RPL state changed to Idle.
233 normal Indicates Ethernet service's state ‐ blocked \ unblocked.
Contains a single parameter: 1 ‐ Description: Ethernet's
state (blocked \ unblocked)
234 normal Ring application: in non‐RPL link indicates first from a
specific RPL was received. Contains a single parameter:
1 ‐ Description: RPM's VLAN ID
235 normal Ring application: in non‐RPL link Ethernet service is
unblocked due to RPM timeout.
236 normal Indicates that the GPS is synchronized with satellites.
237 normal Indicates that encryption is OK. Contains a single
parameter which is its description including the HSU's
name
238 normal Indicates that encryption is OK. Contains a single
parameter which is its description including the HSU's
name
239 normal
Indicates a registered HSU is synchronized.
240 normal Indicates when HBS has been activated.
241 normal Switching Channel Bandwidth.
242 normal HBS Tx ratio has changed.
Release 3.5.70 C‐78