MIB Traps
Table C‐4: MIB Traps (Sheet 6 of 8)
Name
tdmServiceClear
ethServiceOpened
encryptionClear
changeLinkPasswordClear
externalAlarmInPort1Clear
externalAlarmInPort2Clear
lanPort1Clear
lanPort2Clear
mngPortClear
externalAlarmInPort3Clear
externalAlarmInPort4Clear
swVersionsMatchFullCompatibilityClear
swVersionsMatchRestrictedCompatibilityClear
swVersionsMatchSoftwareUpgradeRequiredClear
swVersionsCompatibleClear
hssMultipleSourcesDisappearedClear
RADWIN 5000 HPMP User Manual
ID
Severity
Description
200
major
Indicates that TDM Service fault is cleared. Contains a
single parameter which is its description: 1 ‐
Description: TDM Service ‐ Normal.
201
normal
Indicates that Ethernet Service has been opened.
Contains a single parameter which is its description: 1 ‐
Description: Ethernet Service has been opened.
203
normal
Indicates that encryption is OK. Contains a single
parameter which is its description: 1 ‐ Description:
Encryption Status ‐ Normal.
204
normal
Indicates that the Link Password was changed
successfully. Contains a single parameter which is its
description: 1 ‐ Description: Link Password has been
changed at/on: %s. %s ‐ Is the Local Site name or
Remote Site name or both sides of the Link.
205
normal
This Trap is sent every time an External Alarm Input fault
of port # 1 is cleared. Contains a single parameter
which is its description: 1 ‐ Description: External Alarm
1 ‐ <User Text> ‐ Alarm Cleared.
206
normal
This Trap is sent every time an External Alarm Input fault
of port # 2 is cleared. Contains a single parameter
which is its description: 1 ‐ Description: External Alarm
2 ‐ <User Text> ‐ Alarm Cleared.
209
normal
Indicates the LAN port 1 status changed to connected.
Contains two parameters: 1 ‐ Description: LAN port 1
status changed to connected ‐ %s 2 ‐ %s Is the Eth.
mode (speed & duplex)
210
normal
Indicates the LAN port 2 status changed to connected.
Contains two parameters: 1 ‐ Description: LAN port 2
status changed to connected ‐ %s. 2 ‐ %s Is the Eth.
mode (speed & duplex).
211
normal
Indicates the management port status changed to
connected. Contains two parameters: 1 ‐ Description:
Management port status changed to connected ‐ %s 2 ‐
%s Is the Eth. mode (speed & duplex)
212
normal
This Trap is sent every time an External Alarm Input fault
of port # 3 is cleared. Contains a single parameter
which is its description: 1 ‐ Description: External Alarm
3 ‐ <User Text> ‐ Alarm Cleared.
213
normal
This Trap is sent every time an External Alarm Input fault
of port # 4 is cleared. Contains a single parameter
which is its description: 1 ‐ Description: External Alarm
4 ‐ <User Text> ‐ Alarm Cleared.
214
normal
The trap is sent if SW versions match. Contains a single
parameter which is its description: 1 ‐ Description:
Software Versions compatible
215
normal
The trap is sent if SW versions match and link
functionality is not restricted. Contains a single
parameter which is its description: 1 ‐ Description:
Software Versions compatible
216
normal
The trap is sent if SW versions match and SW upgrade is
successful. Contains a single parameter which is its
description: 1 ‐ Description: Software Versions
compatible
217
normal
The trap is sent if SW versions compatible Contains a
single parameter which is its description: 1 ‐
Description: Software Versions compatible
218
normal
Indicates that multiple sync pulse sources disappeared.
Contains a single parameter which is its description: 1 ‐
Description: HSS multiple sync pulse sources
disappeared.
Release 3.5.70
C‐77