Radwin 5000 HPMP User Manual page 445

Private MIB Parameters
Table C‐2: Private MIB Parameters ‐ HBS (Sheet 21 of 33)
Name
winlink1000IduAdmVlanSupported
winlink1000IduAdmVlanEgressMod
e
winlink1000IduAdmVlanIngressMo
de
winlink1000IduAdmVlanDefaultPor
tVIDs
winlink1000IduAdmVlanLan1Untag
gedVIDs
winlink1000IduAdmVlanLan2Untag
gedVIDs
winlink1000IduAdmVlanSfpUntagg
edVIDs
winlink1000IduAdmVlanLan1Filtere
dVIDs
winlink1000IduAdmVlanLan2Filtere
dVIDs
winlink1000IduAdmVlanSfpFiltered
VIDs
winlink1000IduAdmPortsConnectio
n
winlink1000IduAdmVlanMode
winlink1000IduAdmVlanMembersh
ipVIDs
winlink1000IduAdmVlanMembersh
ipPortsCode
winlink1000IduAdmVlanMembersh
ipUntaggedHandle
winlink1000IduAdmVlanMembersh
ipTagUntagged
winlink1000IduSrvDesiredTrunks
winlink1000IduSrvServices
winlink1000IduSrvActiveTrunks
RADWIN 5000 HPMP User Manual
OID Type
Release 3.5.70
Description
RO Identifies if the local IDU supports VLAN tag/
untag
RW VLAN tag/untag egress values
RW VLAN tag/untag ingress values
RW VLAN tag/untag default VLAN ids for each port ‐
Right most digit is Vlan priority (0‐6) other digits
compose Vlan Id (1‐4094)
RW VLAN untagged VIDs for LAN1 port
RW VLAN untagged VIDs for LAN2 port
RW VLAN untagged VIDs for Sfp port
RW VLAN filtered VIDs for LAN1 port
RW VLAN filtered VIDs for LAN2 port
RW VLAN filtered VIDs for Sfp port
RW IDU ports connection bitmap. bit 0 ‐ LAN1‐
LAN2 bit 1 ‐ SFP‐LAN1 bit 2 ‐ SFP‐LAN2 bit
values: 0 ‐ ports are disconnected. 1 ‐ ports
are connected.
RW Local IDU Vlan Mode.
RW VLAN Membership VLAN IDs list.
RW VLAN Membership ports code. Each value
represent the relation (bitmap) Between the
suitable VID to the IDU ports. bit 0 ‐ LAN1 bit
1 ‐ LAN2 bit 2 ‐ SFP bit value 0 ‐ not member
of appropriate VID bit value 1 ‐ member of
appropriate VID
RW VLAN Membership Untagged frames handling.
The 3 values representing LAN1 LAN2 and SFP
accordingly. For each port the optional values
are: 1 ‐ Discard 2 ‐ Tag 3 ‐ Leave Unmodified
RW VLAN Membership Untagged frames tagging.
The 3 values representing LAN1 LAN2 and SFP
accordingly. The value on each port entry
represent the tagging value which is built of:
VLAN ID & VLAN Priority.
RW Required trunks bitmap. Note that the number
of possible trunks that can be configured may
vary based on the IDU hardware configuration
the selected air interface rate and the range of
the installation. The provided Manager
application enables the user to select only
available configurations. A change is effective
immediately if applied to a master unit and the
link is in service mode.
RO This parameter is reserved to the Manager
application provided with the product.
RO A bitmap describing the currently open TDM
trunks.
C‐26