MIB Traps
Table C‐4: MIB Traps (Sheet 3 of 8)
Name
hbsUnregisteredUnsynchronizedHsu
cableQuality
httpAuthentication
telnetAuthentication
tdmServiceAlarm
ethServiceClosed
ethServiceNotPermitted
encryptionAlarm
changeLinkPasswordAlarm
externalAlarmInPort1Alarm
externalAlarmInPort2Alarm
bitFailedAlarm
wrongConfigurationLoadedAlarm
lanPort1DisconnectedAlarm
lanPort2DisconnectedAlarm
mngPortDisconnectedAlarm
externalAlarmInPort3Alarm
RADWIN 5000 HPMP User Manual
ID
Severity
Description
31
normal
Indicates an unregistered HSU lost synchronization.
32
normal
1Gbps rate is not supported due to bad line quality.
33
normal
HTTP Authentication Failure.
34
normal
Telnet Authentication Failure.
100
major
Indicates that TDM Service is in alarm state. Contains a
single parameter which is its description: 1 ‐
Description: TDM Service ‐ Alarm.
101
major
Indicates that Ethernet Service is closed. Contains a
single parameter which is its description: 1 ‐
Description: Ethernet Service is closed.
102
major
Indicates that Ethernet Service is not permitted.
Contains a single parameter which is its description: 1 ‐
Description: A valid IDU could not be detected at %s.
Please check your configuration. %s ‐ Is the Local Site
name or Remote Site name or both sides of the Link.
103
major
Indicates an encryption key mismatch. Contains a
single parameter which is its description: 1 ‐
Description: Encryption Status ‐ Failed. No Services are
available.
104
major
Indicates that a failure has occurred while attempting to
change the Link Password. Contains a single parameter
which is its description: 1 ‐ Description: Failed to
change the Link Password at/on: %s. %s ‐ Is the Local
Site name or Remote Site name or both sides of the
Link.
105
major
The trap is sent every time an alarm occurs in the
External Alarm Input of port #1. Contains a single
parameter which is its description: 1 ‐ Description:
External Alarm 1 ‐ <User Text> ‐ Alarm.
106
major
The trap is sent every time an alarm occurs in the
External Alarm Input of port #2. Contains a single
parameter which is its description: 1 ‐ Description:
External Alarm 2 ‐ <User Text> ‐ Alarm.
107
major
The trap is sent if there is no way to recover from the
situation.Contains two parameters: 1 ‐ Description:
ODU power up built in test failed. Error code is: %n 2 ‐
%n number
108
major
The trap is sent if there is a way to recover from the
situation.Contains two parameters: 1 ‐ Description:
Wrong configuration loaded. Error code is: %n 2 ‐ %n
number
109
major
Indicates the LAN port 1 status changed to
disconnected.Contains a single parameter which is its
description: 1 ‐ Description: LAN port 1 status changed
to disconnected.
110
major
Indicates the LAN port 2 status changed to
disconnected.Contains a single parameter which is its
description: 1 ‐ Description: LAN port 2 status changed
to disconnected.
111
major
Indicates the management port status changed to
disconnected.Contains a single parameter which is its
description: 1 ‐ Description: Management port status
changed to disconnected.
112
major
The trap is sent every time an alarm occurs in the
External Alarm Input of port #3. Contains a single
parameter which is its description: 1 ‐ Description:
External Alarm 3 ‐ <User Text> ‐ Alarm.
Release 3.5.70
C‐74