Radwin 5000 HPMP User Manual page 449

Private MIB Parameters
Table C‐2: Private MIB Parameters ‐ HBS (Sheet 25 of 33)
Name
winlink1000IduTdmType
winlink1000IduTdmTypeEval
winlink1000IduTdmLineStatusStr
winlink1000IduTdmHotStandbySup
port
winlink1000IduTdmDesiredHotStan
dbyMode
winlink1000IduTdmHotStandbyOpe
rationStatus
winlink1000IduTdmBackupLinkConf
iguration
winlink1000IduTdmLineInterfaceCo
nfiguration
winlink1000IduTdmLineImpedance
Configuration
winlink1000HbsAirState
winlink1000HbsAirOpMode
winlink1000HbsAirAvailTimeSlots
winlink1000HbsAirSectorCbwSuppo
rtedStr
winlink1000HbsAirCompressedMon
winlink1000HbsAirConfChanges
winlink1000HbsAirConfTable
winlink1000HbsAirConfEntry
winlink1000HbsAirConfIndex
winlink1000HbsAirConfUpMir
winlink1000HbsAirConfDownMir
winlink1000HbsAirConfHsuName
winlink1000HbsAirConfHsuLocation
winlink1000HbsAirConfDualAntTxM
ode
winlink1000HbsAirConfNumOfTs
winlink1000HbsAirConfGeoLocatio
n
winlink1000HbsAirConfHsuType
winlink1000HbsAirConfHsuLevel
RADWIN 5000 HPMP User Manual
OID Type
Release 3.5.70
Description
RW TDM Type (The value undefined is read‐only).
RW TDM Type for evaluation.
RO Line status.
RO Indicates if Hot Standby is supported.
RW Desired Hot Standby Mode.
RO The Link Actual Status.
RW The current configuration of the backup link.
RW TDM Line interface configuration.
RW TDM line impedance configuration (standardT1 ‐
100Ohm nonStandardT1 ‐ 110Ohm)
Applicable only for T1 TDM type.
RO Holds the state of the HBS.
RW Holds the operation mode of the HBS.
RO This parameter holds the number of available
time slots (not in use) in the air interface.
RO Represents the channel bandwidth which is
supported by the HBS and all connected HSUs.
RO Holds HBS monitor data in compressed format:
HBS Traffic Monitor In Bytes(4) Out Bytes(4)
In Frames(4) Out Frames(4) HBS State (1) HBS
Freq (4) Number of Links (2) EC Change
Counter (4) Current Ratio (2) Total Air Frames
(4) HBS Rx Rate in Kbps (4) HBS Tx Rate in Kbps
(4) HBS Rx Rate in Fps (4) HBS Tx Rate in Fps
(4) HBS Set Mode (1).
RO 16 characters that represent 16 HSUs. Each
time a configuration is been changed increment
the relevant character.
N/A Holds the table for all registered HSUs in the
sector (16 entries).
N/A HSUs configuration table entry. INDEX {
winlink1000HbsAirConfIndex }
RO HSUs configuration table index.
RW Uplink MIR towards specific HSU in units of
kbps.
RW Downlink MIR towards specific HSU in units of
kbps.
RW HSU name.
RW HSU location.
RW Transmission type when using Dual Antenna on
both link's sides. spatial Multiplexing Diversity
(using a single spatial stream) and Auto
Selection (OMS control).
RW Number of time slot which are allocated to
specific HSU.
RW Geographic device location in format: latitude
longitude.
RW HSU type (1 = Fixed 2 = Stationary 3 = Mobile 4
= Transport)
RW HSU level (1 .. 4)
C‐30