Engine General Information And Diagnosis; Precautions; Precautions On Engine Service; Precaution On On-Board Diagnostic (Obd) System - Suzuki Swift Sport 2004 Service & Repair Manual

Engine General Information and Diagnosis

Engine

Precautions on Engine Service

CAUTION
!
The following information on engine service
should be noted carefully, as it is important in
preventing damage, and in contributing to
reliable engine performance.
• When raising or supporting engine for any reason, do
not use a jack under oil pan. Due to small clearance
between oil pan and oil pump strainer, jacking against
oil pan may cause it to be bent against strainer,
resulting in damaged oil pick-up unit.
• It should be kept in mind, while working on engine,
that 12-volt electrical system is capable of violent and
damaging short circuits.
When performing any work where electrical terminals
can be grounded, ground cable of the battery should
be disconnected at battery.
• Any time the air cleaner, throttle body or intake
manifold is removed, the intake opening should be
covered. This will protect against accidental entrance
of foreign material which could follow intake passage
into cylinder and cause extensive damage when
engine is started.
Precaution on On-Board Diagnostic (OBD)
System
There are two types of On-Board Diagnostic (OBD)
system, Euro OBD system and non-Euro-OBD system,
depending on the vehicle specification.
As the diagnosis function is different between these two
types, be sure to fully understand the OBD system
referring to "On-Board Diagnostic System Description".
OBD System Summary Table
Euro OBD
model
Quantity of DTC Approx. 80
related to engine
control
Freeze frame Available
data
SUZUKI scan Available
tool
OBD generic Available
scan tool

Precautions

Precautions in Diagnosing Trouble

S7RS0B1100001
• Don't disconnect couplers from ECM, battery cable
• Diagnostic information stored in ECM memory can be
S7RS0B1100005
• Priorities for diagnosing troubles
Non-Euro-OBD
model
Approx. 60
Not available
Available
Not available
Engine General Information and Diagnosis:
NOTE
There are two types of OBD system
depending on the vehicle specification.
For details, refer to "Precaution on On-Board
Diagnostic (OBD) System".
from battery, ECM ground wire harness from engine
or main fuse before confirming diagnostic information
(DTC, freeze frame data, etc.) stored in ECM memory.
Such disconnection will erase memorized information
in ECM memory.
cleared as well as checked by using SUZUKI scan
tool or OBD generic scan tool. Before using scan tool,
read its Operator's (Instruction) Manual carefully to
have good understanding as to what functions are
available and how to use it.
For Euro OBD model it is indistinguishable which
module turns on MIL because not only ECM but also
TCM (A/T model) turns on MIL (For details of on-
board diagnostic system for A/T model, refer to "On-
Board Diagnostic System Description in Section 5A").
Therefore, check both ECM and TCM (A/T model) for
DTC when MIL lights on.
When checking ECM for DTC, keep in mind that DTC
is displayed on the scan tool as follows depending on
the scan tool used.
– SUZUKI scan tool displays DTC detected by ECM.
– OBD generic scan tool displays DTC detected by
each of ECM and TCM (A/T model) simultaneously.
If two or more DTCs are stored, proceed to the DTC
flow which has been detected earliest in the order and
follow the instruction in that flow.
If no instructions are given, troubleshoot DTCs
according to the following priorities.
a. DTCs other than DTC P0171 / P0172 (Fuel
system too lean / too rich), DTC P0300 / P0301 /
P0302 / P0303 / P0304 (Misfire detected) and
DTC P0401 / P0402 (EGR flow malfunction)
b. DTC P0171 / P0172 (Fuel system too lean / too
rich) and DTC P0401 / P0402 (EGR flow
malfunction)
c. DTC P0300 / P0301 / P0302 / P0303 / P0304
(Misfire detected)
1A-1
S7RS0B1100002