Pairing - Yamaha RIVAGE PM10 Operation Manual

Basic Operations  Pairing

Pairing

You can pair adjacent channels for stereo operation.
■ Input channels
You can pair either odd/even-numbered channels or even/odd-numbered channels. For single input
channels (monaural), the pan level is nominal at the center, and +3 dB at hard left or hard right. For
paired input channels, the balance level is nominal at the center, and +3 dB at hard left or hard right.
If two channels are paired, their parameters (with the exception of delay) will be linked.
■ MIX buses and MATRIX buses
You can pair adjacent odd/even-numbered MIX buses or MATRIX buses. If two channels are paired,
their parameters (with the exception of delay) will be linked.
Setting or defeating pairing on the panel
1.
For the two adjacent channels, hold down the [SEL] key of one, and press the
[SEL] key of the other.
The sequence of the two [SEL] keys will determine which channel parameters will be copied to
the other channel. When you pair channels, the parameters of the channel you pressed first
will be copied to the subsequently-pressed channel. For example, if you want to pair channel 1
and channel 2, press and hold down the channel 1 [SEL] key, and then press the channel 2
[SEL] key. The channel 1 parameter status will be copied to channel 2.
For information on the parameters that can be copied or linked by the pair setting, refer to the
data list.
2.
To defeat pairing, press and hold down the [SEL] keys of both channels.
When MIX buses are paired, the signal flow will change as described below:
CH to MIX
FIX
to MIX(FIX)
POST ON
MONO to MONO
to MIX(FIX)
POST PAN L
MONO to STEREO
POST PAN R
to MIX(FIX)
POST ON
STEREO to MONO
POST ON
to MIX(FIX)
POST PAN L
STEREO to STEREO
POST PAN R
CH to MIX
VARI
to MIX/MATRIX(VARI) PRE FILTER
PRE EQ
MONO to MONO PRE DYNA1
PRE DYNA2
PRE FADER
POST FADER
POST ON
to MIX/MATRIX(VARI) PRE FILTER
PRE EQ
MONO to STEREO
PRE DYNA1
PRE DYNA2
PRE FADER
POST FADER
POST ON
to MIX/MATRIX(VARI)
STEREO to MONO PRE FILTER
PRE EQ
PRE DYNA1
L CH PRE DYNA2
PRE FADER
POST FADER
POST ON
PRE FILTER
PRE EQ
PRE DYNA1
R CH PRE DYNA2
PRE FADER
POST FADER
POST ON
to MIX/MATRIX(VARI)
STEREO to STEREO PRE FILTER
PRE EQ
PRE DYNA1
L CH
PRE DYNA2
PRE FADER
POST FADER
POST ON
PRE FILTER
PRE EQ
PRE DYNA1
R CH PRE DYNA2
PRE FADER
POST FADER
POST ON
31
CONTENTS FUNCTION MAP
ON
to MIX1
to MIX2-72
(same as above)
to MIX1
ON
to MIX2
to MIX3-72
(same as above)
to MIX1
ON
to MIX1
to MIX2-72
(same as above)
to MIX1
ON
to MIX2
to MIX3-72
(same as above)
LEVEL
ON
to MIX1(MATRIX1)
to MIX2-72(MATRIX2-36)
(same as above)
PAN to MIX1(MATRIX1)
LEVEL
ON
to MIX2(MATRIX2)
to MIX3-72(MATRIX3-36)
(same as above)
LEVEL
ON
to MIX1(MATRIX1)
to MIX1(MATRIX1)
to MIX2-72(MATRIX2-36)
(same as above)
LEVEL
ON
to MIX1(MATRIX1)
to MIX2(MATRIX2)
BALANCE
to MIX3-72(MATRIX3-36)
(same as above)
RIVAGE PM10 Operation Manual
FAQ
MIX1-72
(MATRIX1-36)
1 2 71 72
MIX1-72
(MATRIX1-36)
1 2 71 72