Electro Industries Shark 200 Installation & Operation Manual page 260

Modbus Address
Hex Decimal
0C0F - 0C10 3088 - 3089 VAR-hours, Net, Phase B
0C11 - 0C12 3090 - 3091 VAR-hours, Net, Phase C
0C13 - 0C14 3092 - 3093 VAR-hours, Total, Phase A
0C15 - 0C16 3094 - 3095 VAR-hours, Total, Phase B
0C17 - 0C18 3096 - 3097 VAR-hours, Total, Phase C
0C19 - 0C1A 3098 - 3099 VA-hours, Phase A
0C1B - 0C1C 3100 - 3101 VA-hours, Phase B
0C1D - 0C1E 3102 - 3103 VA-hours, Phase C
Phase Angle Block
1003 - 1003 4100 - 4100 Phase A Current
1004 - 1004 4101 - 4101 Phase B Current
1005 - 1005 4102 - 4102 Phase C Current
1006 - 1006 4103 - 4103 Angle, Volts A-B
1007 - 1007 4104 - 4104 Angle, Volts B-C
1008 - 1008 4105 - 4105 Angle, Volts C-A
Status Block
1193 - 1193 4500 - 4500 Port ID
1194 - 1194 4501 - 4501 Meter Status
1195 - 1195 4502 - 4502 Limits Status
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6)
SINT32 -99999999 to 99999999 VARh per energy format
SINT32 -99999999 to 99999999 VARh per energy format
SINT32 0 to 99999999
SINT32 0 to 99999999
SINT32 0 to 99999999
SINT32 0 to 99999999
SINT32 0 to 99999999
SINT32 0 to 99999999
SINT16 -1800 to +1800
SINT16 -1800 to +1800
SINT16 -1800 to +1800
SINT16 -1800 to +1800
SINT16 -1800 to +1800
SINT16 -1800 to +1800
UINT16 1 to 4
UINT16 bit-mapped
UINT16 bit-mapped
Doc# E149701
B: Modbus Map and Retrieving Logs
Units or Resolution
VARh per energy format
VARh per energy format
VARh per energy format
VAh per energy format
VAh per energy format
VAh per energy format
0.1 degree
0.1 degree
0.1 degree
0.1 degree
0.1 degree
0.1 degree
none Identifies which Shark COM port a master is connected
to; 1 for COM1, 2 for COM2, etc.
mmmpch-- tffeeccc mmm = measurement state (0=off, 1=running normally,
2=limp mode, 3=warmup, 6&7=boot, others unused)
See note 16.
pch = NVMEM block OK flags (p=profile, c=calibration,
h=header), flag is 1 if OK
t - CT PT compensation status. (0=Disabled,1=Enabled)
ff = flash state (0=initializing, 1=logging disabled by
Vswitch, 3=logging)
ee = edit state (0=startup, 1=normal, 2=privileged
command session, 3=profile update mode)
ccc = port enabled for edit(0=none, 1-4=COM1-COM4,
7=front panel)
87654321 87654321 high byte is setpt 1, 0=in, 1=out
low byte is setpt 2, 0=in, 1=out
see notes 11, 12, 17
Comments # Reg
2
2
2
2
2
2
2
2
Block Size: 104
read-only
1
1
1
1
1
1
Block Size: 6
read-only
1
1
1
MM-10