Arrayloc Troubleshooting Tree - Matching Projectors For Color And Brightness - Christie Entero RPMWU User Manual

6.6.6 ArrayLOC Troubleshooting Tree - Matching Projectors for Color and Brightness

Troubleshooting ArrayLOC -
START HERE
Go to the Main > Configuration (4) > ArrayLOC (13) >
Bright/ColorLOC Configuration (3) menu.
Select the Array Status menu item to display the
Bright/ColorLOC Array Status.
Do the colors and brightness of
the array projectors match?
Yes
Is the array brightness the
expected brightness?
Yes
Are the array colors (red, green,
blue, white) the expected colors?
A3
Note!
Projector Color Adjustments (PCAs) are specific to
each Target Color Space, so when the selected Target
Color Space is changed the adjustments from a
previously tuned color space should be copied as a
baseline for the adjustments in the new color space and if
necessary, projector tuning repeated.
A5
No
A10
Are the missing projectors
correctly wired to the
ArrayLOC network?
No
Yes
A11
Is the ArrayLOC Network
on missing projector(s) set to the
correct network?
No
C5
Entero RPMWU/RPMSP/RPMHD-LED01 User Manual
020-100367-05 Rev.1 (06-2012)
A3 B4 C7 C8 C9
B1 C3 C12
Menu
Reference
A7
A1
No
A8
Note!
Projectors can be removed from the ArrayLOC
array by any of the following methods:
(a) Turning the projector OFF
(b) Disconnecting the ArrayLOC network
B1 (if using the PHM Network)
No
(c) Setting the Bright/ColorLOC Mode to OFF
(d) Setting the Bright/ColorLOC Group to a
different number
C1
No
Yes – Feedback Sensor
Uncalibrated
Yes – Min Gamut
Not Met
Does the Status page on
missing projector(s) show any
A1
BCLOC errors?
No
A12
Are the missing projector(s)
Yes
set to the correct BCLOC Mode?
Menu > Configuration > Service > ArrayBCLOC
Yes
Configuration (Password-protected menu)
A14 A13
Are the missing projector(s)
Is the Broadcast Interval set
Yes Yes set to the correct
to an appropriate value?
Bright/ColorLOC Group?
No
Menu > Configuration > ArrayLOC > Projector Color Adjustment
Menu > Configuration > ArrayLOC > Array Color Target
A11
Menu > Configuration > ArrayLOC > ArrayLOC Configuration
B2
Menu > Configuration > ArrayLOC > Bright/ColorLOC Configuration
Recalibrate the internal
sensor of the problem
projectors
OR
Call Tech Support
Yes – Min Brightness
Not Met
Proceed to Fine
Tuning of Projected
Copy PCAs from
Colors (Managing
Colors with ArrayLOC tuned
in Section 3) Target Color Space
No No
A3
A2
Do the PCAs for the
Has the array selected array Target
Yes Yes
been tuned? Color Space match the
PCAs from the tuning?
Yes
Does the array projector count
equal the expected number of Bright/ColorLOC Array Status
projectors?
< Target
Flags
W
No
r wW*
W
gbW
No
A5
Menu > Status
C11
Menu > Configuration > Service > Color Saturation
C10
Menu > Configuration > Service > Advanced Color Adjustment
A12 A13 A14 C4
Menu > Configuration > Service > ArrayLOC Service
Done
A9 Yes
Does replacing the LMs of
No the problem projectors resolve
the problem?
A8 No
Does removing the problem C7
Yes projectors from the ArrayLOC
C11
array resolve the problem?
Yes
A7
Are the Minimum Gamut and
Minimum Brightness thresholds
set to appropriate levels?
No
A6 Yes
Has the ArrayLOC been ON
for at least 2 minutes?
No
C12
No
A4
Is the problem
C1
with the array
color?
4 Target Gamut 800 330 160 800 125 000 313
Common Gamut 687 306 193 738 150 34 313 329
ProjID Group Int Age Rx Ry RY Gx Gy GY Bx By BY Wx Wy
1 211 1 1 692 304 283.2 185 748 696.8 139 28 67.2 313 329
0 211 1 1 687 306 109.9 193 741 123.4 145 23 17.9 313 329
2 211 1 1 699 296 416.5 188 745 778.5 141 29 91.7 313 329
3 211 1 1 700 295 343.7 181 749 700.9 149 23 57.3 313 329
Section 6: Troubleshooting Tree
329 1000
350
WY
369.1
361.2
418.0
390.5
6-9