Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Christie DHD675-E
Summary of Contents for Christie DHD675-E
- Page 1 E Series DHD675-E/DWU675-E/DHD775-E/DWU775-E U S E R M A N U A L 020-000515-01...
- Page 2 Addendum The CD included with this printed manual contains an electronic copy in English. Please read all instructions before using or servicing this product. Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les instructions avant d'utiliser ou de réparer ce produit.
- Page 3 Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense. WARNING! Changes or modifications not expressly approved by Christie could void the user’s authority to operate the product.
-
Page 4: Preventative Maintenance
Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. -
Page 5: Table Of Contents
4.9.7 Administrator Page ....................4-27 4.9.8 About Page ......................4-27 4.10 Christie Presenter ......................4-28 4.10.1 Connect to the Projector and Download Christie Presenter Software ....4-28 4.10.2 Install Christie Presenter software ..............4-30 4.10.3 Use Christie Presenter ..................4-31 4.11 Card Reader Operation ....................4-36 4.12 Install the Lamp ......................4-40... - Page 6 Table of Contents 5. TROUBLESHOOTING 6. SPECIFICATIONS 6.1 Inputs ..........................6-1 6.2 PIP/PBP Compatibility ....................6-2 6.3 Key Features ........................6-3 6.4 List of Components .......................6-4 6.5 Optional Accessories ....................6-4 6.6 REGULATORY ......................6-5 6.7 Declaration of Conformity for EU Countries ..............6-7 6.8 Federal Communications Commission (FCC) Warning ..........6-7 6.9 MENU TREE.........................6-8 E Series User Manual 020-000515-01 Rev.
-
Page 7: Safety
Change the lamp when the warning message appears. All installation and maintenance procedures must be performed by a Christie accredited service technician. Keep all combustible material away from the concentrated light beam of the projector. - Page 8 Section 1: Safety Always power down the projector and disconnect all power sources before servicing or cleaning. Use a soft cloth moistened with a mild detergent to clean the display housing. Disconnect the power plug from the AC outlet if the product is not being used for an extended period of time.
-
Page 9: Introduction
Section 2: Introduction INTRODUCTION The product specified in this document is a high brightness, high-resolution video/graphics 1-chip mercury lamp based projector. The projector is available in HD and WUXGA resolutions. The projector utilizes Digital Light Processing (DLP ® ) technology from Texas Instruments. It is primarily designed for fixed installation markets. - Page 10 Section 2: Introduction Ind. Part Name Description Lens door Use the lens door to access the lens module. Receives signals from the IR remote. Keep the signal Front IR Sensor path to the sensor unobstructed for uninterrupted communication with the projector. Allows automated lens control and adjustment: vertical Projection Lens and horizontal offsets, zoom and focus.
-
Page 11: Built-In Keypad
Section 2: Introduction Built-in Keypad Ind. Key Name Description Power Turn the projector on or off. Menu Display menus Auto Automatically optimize image Lens Adjust the lens vertical or horizontal offset setting Focus Adjust focus Exit Return to previous level or exit menus if at top level Adjust a setting UP or DOWN Arrow Keys Navigate within a menu... -
Page 12: Input/Output (I/O) Panel
Section 2: Introduction Input/Output (I/O) Panel Ind. Connector Name Ind. Connector Name Ind. Connector Name S-Video CVBS Red/Pr Blue/Pb Green/Y RS232 IN Mini USB Ethernet Remote Display Port VGA-OUT VGA-IN HDMI-1 HDMI-2 E Series User Manual 020-000515-01 Rev. 2 (03-2013) -
Page 13: Remote Control
Section 2: Introduction Remote Control E Series User Manual 020-000515-01 Rev. 2 (03-2013) - Page 14 Section 2: Introduction Ind. Key Name Description Picture Mute Display or blank the video image Power on Turn projector ON Gamma Adjust mid-range levels Bright Adjust amount of light in the image PIP/PBP Turn PIP/PBP ON/OFF Size Adjust the PIP/PBP size Number Keys Enter a number, such as a channel, value, etc Help...
-
Page 15: Led Status Indicators
Section 2: Introduction LED Status Indicators The LED status indicators are located on the rear of the projector. LAMP 1 LED LED Status Projector State Failed to strike lamp after 5 attempts (strike attempts will stop). Red (short blink) Lamp has unexpectedly shut down (system goes into cool down state). - Page 16 Section 2: Introduction STATUS LED LED Status Projector State Projector is in OFF state (without AC plug in) Yellow (no blink) Projector is in standby mode (AC plug in) Yellow long blink Projector is in startup state Yellow long blink Projector is in cool down state Flashing Green/ Projector is in flash update state...
-
Page 17: Installation
Section 3: Installation INSTALLATION Connect to Computer Desktop Laptop MOLEX Ind. Connector Name Ind. Connector Name Ind. Connector Name VGA out Cable VGA in Cable RS232 Cable Mini USB to USB A Type WiFi USB Dongle or thumb Network Cable Cable drive HDMI to DVI Cable... -
Page 18: Connect To Video Equipment
Section 3: Installation Connect to Video Equipment DVD player Component video output equipment Video cassette recorder Ind. Connector Name Ind. Connector Name Ind. Connector Name S-Video Cable Composite Video Cable HDMI Cable 3 RCA Component 15-Pin to 3 RCA Component/ VGA to RGB SCART Cable HDTV Adaptor... -
Page 19: Turn The Projector On
Section 3: Installation Turn the Projector On Ensure that the power cord and signal cable are securely connected. The Power button on the built in keypad is illuminated. 9 10 11 12 13 14 15 16 17 18 19 20 Turn on the lamp by pressing on the remote control or press “... -
Page 20: Adjust The Projector Position
Section 3: Installation Adjust the Projector Position When you select a position for the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Follow these general guidelines: Position the projector on a flat surface at a right angle to the screen. -
Page 21: Calculate Lens Offset
Section 3: Installation Calculate Lens Offset The vertical image offset (shift) ranges for the projector are +120%/-40% (WUXGA) and +134%/-40% (HD). Offset is +720 pixels for both WUXGA and HD. The horizontal image offset is +/-20% (+/- 192 pixels). NOTE: The 0.8:1 lens is the only exception and must be used on axis. - Page 22 Section 3: Installation Vertical Image Offset: 120% Offset (WUXGA) Image has been offset 720 pixels above lens center, so the center of the image is now 720 pixels above where the center of the image was at 0% offset (or lens center). The offset is +720/600 * 100% = +120%.
- Page 23 Section 3: Installation HD Projectors: Vertical Image Offset: 0% Offset (HD) No offset is applied - 0% offset. Half of the image appears above lens center and half of the image appears below lens center. 540 pixels above lens center. Lens center 540 pixels below lens...
- Page 24 Section 3: Installation Vertical Image Offset: -40% Offset (HD) Image has been offset 216 pixels below lens center, so the image has an offset of -216/540 * 100% = -40% 216 pixels Lens center of shift below lens center. Total of 756 pixels (540+216) of display...
-
Page 25: Removing And Installing The Lens
Section 3: Installation Removing and Installing the Lens When handling the projector after lens installation, make sure the front lens cap is placed on the lens to protect the lens surface from potential damage. When carrying or moving the projector, do not handle by the lens. This may damage the lens, the chassis or other mechanical parts within the projector. -
Page 26: Ceiling Mount Installation
The projector can be inverted and suspended from the ceiling using a specially designed ceiling mount fixture. For more information, contact your dealer. Use only the Christie approved ceiling mount kit (133-106108-02) designed for your projector. When not mounted properly, the projector may fall, causing hazards or injury. -
Page 27: Stacking Installation
All attachment points to be secured 3.9.2 Stacking The E Series projectors can be stacked up to a maximum of 3 projectors high using the Christie stacking frame (118-100107-01). Description 1) Base Plate 2) Locking pin 3) Cable Tie-off Frame... -
Page 28: Stacking Multiple Projectors
Section 3: Installation Install the adapter plate on the E Series projector (described in 3.9.1) before mounting to the stacking frame. Make sure the pitch is to its maximum, prior to placing the projector from the front. Place the projector into the stacking frame. NOTE: There are two ways of placing the projector into the stacking frame: from the top or from the front. -
Page 29: Stacking Alignment
Section 3: Installation Insert the locking pin through the holes in the stacking legs. Make sure each pin is fully inserted. NOTE: The steel ball on the end of the pin keeps the pin from releasing inadvertently. ™ Hole Stacking Press botton to Inserted remove or install... -
Page 30: Operation
Section 4: Operation OPERATION The projector has multilingual On-Screen Display (OSD) menus that allow you to make image adjustments and change a variety of settings. • Most of the projector controls are accessed from within the projector menu system. There are several groups of related functions, with each group selectable from the Main menu as shown below. -
Page 31: Size And Position Menu
Section 4: Operation Size and Position Menu Size Presets Display an image with the detected size, or resize the image by maximizing either the height, width or both, or resize to the maximum size possible while keeping the original aspect ratio. Auto: Display with the detected size. - Page 32 Section 4: Operation Pixel Phase Analog RGB signals only. Adjust pixel phase when the image still shows shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the phase of the pixel-sampling clock relative to the incoming signal. Horz Position Move the image right or left within the area of available pixels.
- Page 33 Section 4: Operation Off: No Geometric correction is applied to the image. Horz Keystone: Adjust the keystone horizontally and make a more square image. Horizontal keystone is used to correct a keystoned image shape in which the left and right borders of the image are unequal in length, and the top and bottom are slanted to one of the sides.
- Page 34 Section 4: Operation Pincushion/Barrel: Allow for correction for slight curved distortion from the lens or projection surface. 4-Corner: Allow the image to be squeezed to fit an area defined by moving each of the four corners’ x and y position. Ind.
-
Page 35: Auto Image
Section 4: Operation Rotation: Allow an image to be rotated – most commonly to level the image. While the image is rotated, the software can crop any content that begins to fall off the panel. The function will not automatically scale the image down to prevent cropping. -
Page 36: Image Settings Menu
Section 4: Operation Image Settings Menu Brightness Adjust the intensity of the image. Contrast Adjust the degree of difference between the lightest and darkest parts of the picture and change the amount of black and white in the image. Color Space Select a color space that has been specifically tuned for the input signal. - Page 37 Section 4: Operation Video Black Level: Analyze the current input image and calculate an offset value which is then added to the analog to digital converter black level value. This ensures optimum black level for each analog source. Detect Film: Control film mode detection and determine whether the original source of the input video was film or video.
- Page 38 Section 4: Operation White Peaking: (video source only) Increase the brightness of whites that are near 100%. Color Temperature: Change the intensity of the colors. Select a listed relative warmth value. Edge Enhancement: Apply the edge enhancement process. E Series User Manual 020-000515-01 Rev.
-
Page 39: Configuration Menu
Section 4: Operation Configuration Menu Language Allows you to select an available language for the OSD display, from English, French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and Russian. Lens Settings Focus and Zoom: Adjust the focus and zoom the image in or out. Lens Shift: Shift the lens up and down or left and right. -
Page 40: Menu Preferences
Section 4: Operation Menu Preferences Menu Horz Position: Change the horizontal position of the OSD. Menu Vert Position: Change the vertical position of the OSD. Show Messages: Display status messages on the screen. Menu Transparency: Change OSD menu background to be transparent. NOTE: As the value increases, more of the image behind the menu is visible. - Page 41 Section 4: Operation Baud Rate: Select the serial port and baud rate. Serial Port Echo: Control whether the serial port echoes characters. Projector Address: Set the projector address (0-9). The projector will respond to IR remotes set either at the same address as the projector or to IR remotes set to address 0.
-
Page 42: Color Matching
Section 4: Operation Color Matching You may require a unique color gamut (range) for a single projector or application, or you may need to precisely match colors across multiple adjacent displays. Use Color Matching by Meter Adjustment or by Manual Adjustment to define the precise hue of each primary color component (red, green, blue and white). - Page 43 Section 4: Operation Green Measured Data Target Data Blue Manual Adjustment Adjust color slide bars and judge image color by eye or meter. A user- defined color “adjustment” can be applied. Use this submenu if you do not have specific color coordinates in mind and will judge color performance by eye or meter.
- Page 44 Section 4: Operation adjusted to optimize picture quality. Color wheel Index (3x): Set Color wheel index to Speed 3X. This setting only needs to be used when the Main Board is changed, and should be adjusted to optimize picture quality. Error log: Show the projector error log for debug.
-
Page 45: Lamp Menu
Section 4: Operation Lamp Menu Lamp Mode Select Constant Power or Constant Intensity mode. Constant Power Set the value of the lamp power (in Watts). Constant Intensity Set the value for the Constant Intensity to maintain constant brightness. A light sensor is used to monitor the light level and will apply more power as the lamp brightness decays naturally over time until it reaches maximum power. -
Page 46: Reset Lamp Hours
Section 4: Operation power-up, or after a set number of hours. Lamp Auto Switch Time Set the number of hours for Lamp Auto Switch. For example: Lamp conditions: lamp 1 = 50 hours, lamp 2 = 60 hours. Set the current lamp to lamp 1 - the lamp with the lower lamp hour usage. -
Page 47: Status Menu
Section 4: Operation Status Menu The read-only Status menu lists a variety of details about the standard and optional components currently detected in the projector. 4-18 E Series User Manual 020-000515-01 Rev. 2 (03-2013) -
Page 48: Input Switching & Pip Menu
Section 4: Operation Input Switching & PIP Menu NOTE: Reference the compatibility table found in Section 6.2. ™ Main Input From the list of active inputs, select one to be used as the main image. PIP/PBP Input From the list of active inputs, select one to be used as the PIP/PBP. PIP/PBP Enable Toggle between displaying two sources at once (Main and PIP/PBP images) or one source only. - Page 49 Section 4: Operation NOTE: PIP/PBP layout and size table as described below. ™ P : indicates primary source region (lighter color). ™ * : Both source regions are the same size. ™ PIP/PBP Size PIP/PBP Layout Small Medium Large PBP, Main left PBP, Main Top PBP, Main Right PBP, Main Bottom...
-
Page 50: Language Menu
Section 4: Operation Input Key Use it to list all of the sources or change the sources. Language Menu Allows you to select an available language for the OSD display. Test Pattern Menu Choose the desired internal test pattern to display, or select OFF to turn off a test pattern. -
Page 51: Web User Interface
Section 4: Operation Web User Interface 4.9.1 Logging On Open your web browser and type the IP address (in the address bar) assigned to your projector. 1 Select the log in level from the Access type drop-down list 2 Enter the Password in the Password field 3 Select the appropriate language from the Language drop-down list. -
Page 52: Main Tabbed Page - Status
Section 4: Operation Projector Information Panel Check the projector information for power status, Pic mute status, OSD status, IP address and Mac address. Switch Panel Switch the on/off status of power, Pic mute, and OSD. 4.9.3 Main Tabbed Page – Status Display the current status of lamp info, cooling (fans), version numbers and signal (source) information 4.9.4 Main Tabbed Page –... -
Page 53: Network
Execute a network restart. This will not change any of the network settings. Network Factory Reset Execute a network factory reset. Network settings will be reset to the following default values: Projector Name = Christie@ + Serial Number Show Network Messages = ON LAN Settings: Manual IP Address = 192.168.0.100 Subnet Mask = 255.255.255.0... - Page 54 Section 4: Operation Start IP = 192.168.1.100 End IP = 192.168.1.120 Subnet Mask = 255.255.255.0 Default Gateway = 192.168.1.100 SNMP Settings: SNMP Read Communication = private Trap IP Address = 0.0.0.0 SMTP IP Address = 0.0.0.0 All other settings are cleared/blanked Trap Configuration: All items = SNMP Trap + Email LAN Panel...
-
Page 55: Tools
Section 4: Operation SNMP Location (default setting: blank) – This field can be used as a description to where a projector is located in a building. SNMP emails sent will specify this location. Trap IP Address (default setting: 0.0.0.0) – This field must be filled in to receive Traps from the projector. -
Page 56: Administrator Page
Section 4: Operation 4.9.7 Administrator Page Add or delete a user or change password 4.9.8 About Page Version Tab View the main firmware version, network firmware version, projector model name, and projector serial number. License Tab The license information of the computer program is displayed. E Series User Manual 4-27 020-000515-01 Rev. -
Page 57: Christie Presenter
Section 4: Operation 4.10 Christie Presenter The Christie Presenter application allows a remote desktop from a host PC to be displayed on the network display through Ethernet, USB, or wireless transports. It can adapt to different network settings (DHCP, fixed IP, and direct link by USB/Ethernet cable). - Page 58 Obtain the WiFi Password from the OSD menu Main Menu > Configuration > Communications > WLAN Connect your PC device to the wireless SSID for the selected projector . Example: “Christie@0112000123”. Enter the password obtained from the OSD WLAN menu. E Series User Manual 4-29 020-000515-01 Rev.
-
Page 59: Install Christie Presenter Software
192.168.1.100) Download and install the Christie Presenter Software Configure the Christie Presenter Software. The name entered is used to identify all computers connected to the projector via the Christie Presenter software via either wired or wireless connections. The Network Display Management ->... -
Page 60: Use Christie Presenter
Section 4: Operation 4.10.3 Use Christie Presenter Press the autorun icon in the system tray to pause or play the USB display. After starting the Christie Presenter application, the main window can been seen (shown below). Icon Description Connect and search network display... - Page 61 Section 4: Operation Connect and search network display Click the button to enter into the connection menu section. If the IP address of the projector is known, enter the IP address and click the "Connect" button. If the IP address is not known, click the "Search"...
- Page 62 Section 4: Operation Select display region Once the connection is set up, click the button to select the size of the projection region: FullScreen, FixedSize, or Alterable. FullScreen: The default capture mode turns to Full screen when the program is launched. At that time, if screen capture starts, the image of the whole screen is transferred to a remote network display.
- Page 63 Section 4: Operation Configure Christie Presenter Click the button to configure Christie Presenter for Basic Setting and Advanced Setting. Basic Setting: Select language, change the region size of fixed size capture mode, and select if notification message popup is allowed.
- Page 64 Section 4: Operation Manage all connected network displays Click the button to control all the users and all the projectors connector to the same projector. Icon Description Administrator log in. Normal user log in. Device is connected. Device is not connected. The icon shows the current status and display position of the local screen on the network display.
-
Page 65: Card Reader Operation
Section 4: Operation 4.11 Card Reader Operation There are four operation modes in the Card Reader application: USB Flash Devices Detection Screen Thumbnail Display Mode Images Display Mode Images Slide Show Mode 4.11.1 USB Flash Device Detection Screen: In this mode, the Card Reader application detects any USB flash devices hot-plug events and displays the flash device icon. - Page 66 Section 4: Operation The user interface is designed to operate the card reader application with a few keys (Enter/Left/Right/Up/Down). The following buttons are supported in the user interface: Previous: Move the selected item left. (Go to previous page when this is the leftmost item) Next: Move the selected item right.
- Page 67 Section 4: Operation Thumbnail: Enter the Thumbnail Display Mode. SlideShow: Enter the Slide Show Mode. Actual Size: Display in actual size of the image. Best Fit: Display the image in best fit to the screen. EXIFDisp OFF/On: Enable/Disable EXIF information display. +90deg: Rotate 90 degree.
- Page 68 Section 4: Operation When the image cannot be displayed due to memory limitation or cannot support image format, the specific image is displayed on the center of the screen. E Series User Manual 4-39 020-000515-01 Rev. 2 (03-2013)
-
Page 69: Install The Lamp
Section 4: Operation 4.12 Install the Lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. -
Page 70: Troubleshooting
Section 5: Troubleshooting TROUBLESHOOTING If you are unable to resolve an issue using the information provided in this section, contact your reseller or service center. Problem Solution No image appears Make sure all the cables and power connections are on-screen correctly and securely connected See “Installation”. - Page 71 Section 5: Troubleshooting Problem Solution Partial, scrolling If you are using a Notebook: or incorrectly Adjust resolution of the computer. displayed image Press the keys listed below for your notebook manufacturer to send signal out from notebook to projector. Example: [Fn]+[F4] Notebook Brand Function Keys Acer...
- Page 72 Section 5: Troubleshooting Problem Solution Image is out of Make sure both lens caps (front and back) are removed. focus Adjust lens focus to fit. Make sure the projection screen is between the required distance. The image is When you play anamorphic DVD or 16:9 DVD, the stretched when projector will show the best image when the projector displaying 16:9...
-
Page 74: Specifications
Section 6: Specifications SPECIFICATIONS Inputs Signal Frame Rate Display- Compo- Resolution HDMI 1 HDMI 2 S- video CVBS Type (Hz) Port nent 640x480 ● ● ● ● ● 640x480 ● ● ● ● ● 640x480 ● ● ● ● ● 800x600 ●... -
Page 75: Pip/Pbp Compatibility
Signal Frame Rate Display- Compo- Resolution HDMI 1 HDMI 2 S- video CVBS Type (Hz) Port nent SECAM SECAM (M) ● ● 480p ● ● ● ● ● ● EDTV 576p ● ● ● ● ● ● 1080i ● ● ●... -
Page 76: Key Features
(Optional) Wireless desktop display using wireless dongle (optional) SNMP traps and e-mail notifications Dual mercury lamp illumination with 330W (DWU/DHD675-E) & 350W (DWU/DHD775-E) 10-bit image processor electronics with modular design All video formats can be resized to full screen either horizontally or... -
Page 77: List Of Components
List of Components This projector comes with all the items shown below. Check to make sure your package is complete. Contact your dealer if anything is missing. IR remote control (133-114117-01) Power cord x 4 UK/Korea/Russia North America Europe Japan DVI to HDMI dongle User manual (CD) NOTE:... -
Page 78: Regulatory
Section 6: Specifications REGULATORY Safety CAN/CSA C22.2 No. 60950-1 UL 60950-1 IEC 60950-1 EN60950 Electro-Magnetic Compatibility Emissions FCC CFR47, Part 15, Subpart B/ICES-003/ANSI C63.4, Class A – Unintentional Radiators AS/NZS CISPR 22/EN55022 Class A - Information Technology Equipment EN 61000-3-2 EN 61000-3-3 Immunity EN55024 EMC Requirements - Information Technology Equipment... - Page 79 Marking This product shall conform to all relevant Canadian, US, and European directives, standards, safety, health and environmental concerns and bear the following markings at product launch: RoHS WEEE Future product markings to include International Certifications: CCC, KC, PSE, c-tick, Gost-R, South Africa International packaging recycling mark requirements: EU Directive (2002/96/EC) on waste and electrical and electronic equipment (WEEE);...
-
Page 80: Declaration Of Conformity For Eu Countries
Section 6: Specifications Declaration of Conformity for EU Countries EMC Directive 2004/108/EC (including amendments) Low Voltage Directive 2006/95/EC Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC Federal Communications Commission (FCC) Warning WARNING A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. -
Page 81: Menu Tree
MENU TREE Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Auto Native Size Presets Auto Letterbox Full Size Full Width Full Height Overscan Zoom By source set Crop Pixel Track 0 - 100 Pixel Phase 0 - 100 Horz Position... - Page 82 Section 6: Specifications Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Image Freeze Off / On Video Film Gamma By source set Bright Normal Look Bright BrilliantColor Bright Look White Peaking 0 - 100 By source set Warmest...
- Page 83 Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Drop Off Curve 70-300 Image Blending Image Gamma 1.8/2.0/2.2/2.4/2.6 Enable On/Off Auto Test Pattern On/Off Intensity of Red 100 - 10000 x of Red 0.300 - 0.700 0.633 y of Red...
- Page 84 Display Port Key number 5 Source Hot-Key Component Key number 6 S-Video Key number 7 Composite Key number 8 Christie Presenter Key number 9 Card Reader Key number 0 Mini USB Change Sources Input key List all Sources Auto Source...
- Page 86 United Kingdom Eastern Europe Singapore Japan ph: +44 118 977 8000 ph: +36 (0) 1 47 48 100 ph: +65 6877-8737 ph: 81-3-3599-7481 France Middle East Beijing South Korea ph: +33 (0) 1 41 21 00 36 ph: +971 (0) 4 299 7575 ph: +86 10 6561 0240 ph: +82 2 702 1601 Germany...