YASKAWA S-V Series User Manual page 226

10 Appendix
Parameter
No.
Input Signal Selection 6
4th
digit digit digit digit
n.    
*7
Pn515
Pn517
Reserved (Do not change.)
Excessive Error Detection Level Between Servo-
*1
Pn51B
motor and Load Position
Pn51E
Excessive Position Error Warning Level
Pn520 Excessive Position Error Alarm Level
Pn522 Reserved (Do not change.)
Pn524 Reserved (Do not change.)
Pn526 Excessive Position Error Alarm Level at Servo ON
Excessive Position Error Warning Level at Servo
Pn528
ON
*1
Speed Limit Level at Servo ON
Pn529
*1
Multiplier per One Fully-closed Rotation
Pn52A
Pn52B Overload Warning Level
Derating of Base Current at Detecting Overload of
Pn52C
Motor
Pn52F Reserved (Do not change.)
∗1. Parameter exclusive for rotational servomotors
∗7. This parameter is for the Large-Capacity Σ-V Series.
10-26
Name
3rd 2nd 1st
Reserved (Do not change.)
Reserved (Do not change.)
Dynamic Brake Answer signal 1 Input Signal Mapping (/DBANS1)
0 Detects dynamic brake (DB) contactor errors when the input signal of CN1-40 is ON (closed) while the DB
is applied.
1 Detects DB contactor errors when the input signal of CN1-41 is ON (closed) while the DB is applied.
2 Detects DB contactor errors when the input signal of CN1-42 is ON (closed) while the DB is applied.
3 Detects DB contactor errors when the input signal of CN1-43 is ON (closed) while the DB is applied.
4 Detects DB contactor errors when the input signal of CN1-44 is ON (closed) while the DB is applied.
5 Detects DB contactor errors when the input signal of CN1-45 is ON (closed) while the DB is applied.
6 Detects DB contactor errors when the input signal of CN1-46 is ON (closed) while the DB is applied.
7 and 8
Disables DB contactor error detection of DB answer signal 1.
9 Detects DB contactor errors when the input signal of CN1-40 is OFF (open) while the DB is applied.
A Detects DB contactor errors when the input signal of CN1-41 is OFF (open) while the DB is applied.
B Detects DB contactor errors when the input signal of CN1-42 is OFF (open) while the DB is applied.
C Detects DB contactor errors when the input signal of CN1-43 is OFF (open) while the DB is applied.
D
Detects DB contactor errors when the input signal of CN1-44 is OFF (open) while the DB is applied.
E Detects DB contactor errors when the input signal of CN1-45 is OFF (open) while the DB is applied.
F Detects DB contactor errors when the input signal of CN1-46 is OFF (open) while the DB is applied.
Reserved (Do not change.)
Setting Factory
Units
Range Setting
−
0000 to FFFF 8888
– – 0000
0 to
1
1073741824
reference 1000
30
unit
(2 )
10 to 100 1%
1 to
1
1073741823
reference 5242880
30
unit
(2 -1)
– –
– –
1073741824
1 to
1
1073741823
reference 5242880
30
unit
(2 -1)
10 to 100 1%
-1
0 to 10000 10000
1 min
0 to 100 1%
1 to 100 1%
10 to 100 1%
−
– 0FFF
When
Classification
Enabled
After restart Setup
–
Immediately Setup
100 Immediately Setup
Immediately Setup
1 –
–
Immediately Setup
100 Immediately Setup
Immediately Setup
20 Immediately Setup
20 Immediately Setup
100 After restart Setup
–
(cont'd)
–
–
–
–