YASKAWA S-V Series User Manual page 209
Ac servo drives indexer module
Hide thumbs
Also See for S-V Series:
- User manual (311 pages) ,
- Safety precautions (33 pages) ,
- User manual (320 pages)
Table of Contents
Advertisement
Parameter
No.
Input Signal Monitor IN1 Polarity
Selection
Bit
0
1
2
3
PnB53
4
5
6
7
Name
Setting Range
0000 to 00FF
Setting
0
The polarity for bit 0 (/SVON) of input signal monitor IN1 is not reversed.
Photocoupler is OFF when bit 0 is 0.
Photocoupler is ON when bit 0 is 1.
1
The polarity for bit 0 (/SVON) of input signal monitor IN1 is reversed.
Photocoupler is ON when bit 0 is 0.
Photocoupler is OFF when bit 0 is 1.
0
The polarity for bit 1 (/ALM-RST) of input signal monitor IN1 is not reversed.
Photocoupler is OFF when bit 1 is 0.
Photocoupler is ON when bit 1 is 1.
1
The polarity for bit 1 (/ALM-RST) of input signal monitor IN1 is reversed.
Photocoupler is ON when bit 1 is 0.
Photocoupler is OFF when bit 1 is 1
0
The polarity for bit 2 (P-OT) of input signal monitor IN1 is not reversed.
Photocoupler is OFF when bit 2 is 0.
Photocoupler is ON when bit 2 is 1.
1
The polarity for bit 2 (P-OT) of input signal monitor IN1 is reversed.
Photocoupler is ON when bit 2 is 0.
Photocoupler is OFF when bit 2 is 1
0
The polarity for bit 3 (N-OT) of input signal monitor IN1 is not reversed.
Photocoupler is OFF when bit 3 is 0.
Photocoupler is ON when bit 3 is 1.
1
The polarity for bit 3 (N-OT) of input signal monitor IN1 is reversed.
Photocoupler is ON when bit 3 is 0.
Photocoupler is OFF when bit 3 is 1
0
The polarity for bit 4 (/DEC) of input signal monitor IN1 is not reversed.
Photocoupler is OFF when bit 4 is 0.
Photocoupler is ON when bit 4 is 1.
1
The polarity for bit 4 (/DEC) of input signal monitor IN1 is reversed.
Photocoupler is ON when bit 4 is 0.
Photocoupler is OFF when bit 4 is 1
0
The polarity for bit 5 (Not used) of input signal monitor IN1 is not reversed.
Bit5 is invalid.
1
The polarity for bit 5 (Not used) of input signal monitor IN1 is reversed.
Bit5 is invalid.
0
The polarity for bit 6 (/RGRT) of input signal monitor IN1 is not reversed.
Photocoupler is OFF when bit 6 is 0.
Photocoupler is ON when bit 6 is 1.
1
The polarity for bit 6 (/RGRT) of input signal monitor IN1 is reversed.
Photocoupler is ON when bit 6 is 0.
Photocoupler is OFF when bit 6 is 1
0
The polarity for bit 7 (Not used) of input signal monitor IN1 is not reversed.
Bit7 is always 0.
1
The polarity for bit 7 (Not used) of input signal monitor IN1 is reversed.
Bit7 is always 0.
10.1 Parameter List for INDEXER Module
Setting
Factory
Unit
Setting
–
0050
Meaning
(cont'd)
When
Reference
Enabled
After restart
7.7.8
Factory Setting
0
0
0
0
1
0
1
0
10-9
10
Advertisement
Table of Contents
Troubleshooting
