3Com S7906E Configuration Manual page 2174

[DeviceA-GigabitEthernet2/0/2] quit
# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and
configure the VLANs mapped to MSTIs 0 through 31 as the protected VLANs of RRPP domain 1.
[DeviceA] rrpp domain 1
[DeviceA-rrpp-domain1] control-vlan 4092
[DeviceA-rrpp-domain1] protected-vlan reference-instance 0 to 31
# Configure Device A as the master node of primary ring 1, with GigabitEthernet 2/0/1 as the primary
port and GigabitEthernet 2/0/2 as the secondary port, and enable ring 1.
[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 2/0/1
secondary-port gigabitethernet 2/0/2 level 0
[DeviceA-rrpp-domain1] ring 1 enable
[DeviceA-rrpp-domain1] quit
# Enable RRPP.
[DeviceA] rrpp enable
2) Configuration on Device B
# Configure the suppression time of physical-link-state changes on GigabitEthernet 2/0/1,
GigabitEthernet 2/0/2, and GigabitEthernet 2/0/3 as zero, disable STP, configure the ports as trunk
ports, and assign them to all VLANs.
<DeviceB> system-view
[DeviceB] interface gigabitethernet 2/0/1
[DeviceB-GigabitEthernet2/0/1] link-delay 0
[DeviceB-GigabitEthernet2/0/1] undo stp enable
[DeviceB-GigabitEthernet2/0/1] port link-type trunk
[DeviceB-GigabitEthernet2/0/1] port trunk permit vlan all
[DeviceB-GigabitEthernet2/0/1] quit
[DeviceB] interface gigabitethernet 2/0/2
[DeviceB-GigabitEthernet2/0/2] link-delay 0
[DeviceB-GigabitEthernet2/0/2] undo stp enable
[DeviceB-GigabitEthernet2/0/2] port link-type trunk
[DeviceB-GigabitEthernet2/0/2] port trunk permit vlan all
[DeviceB-GigabitEthernet2/0/2] quit
[DeviceB] interface gigabitethernet 2/0/3
[DeviceB-GigabitEthernet2/0/3] link-delay 0
[DeviceB-GigabitEthernet2/0/3] undo stp enable
[DeviceB-GigabitEthernet2/0/3] port link-type trunk
[DeviceB-GigabitEthernet2/0/3] port trunk permit vlan all
[DeviceB-GigabitEthernet2/0/3] quit
# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and
configure the VLANs mapped to MSTIs 0 through 31 as the protected VLANs of RRPP domain 1.
[DeviceB] rrpp domain 1
[DeviceB-rrpp-domain1] control-vlan 4092
[DeviceB-rrpp-domain1] protected-vlan reference-instance 0 to 31
# Configure Device B as a transit node of primary ring 1, with GigabitEthernet 2/0/1 as the primary port
and GigabitEthernet 2/0/2 as the secondary port, and enable ring 1.
1-23