YASKAWA iQpump1000 User Manual page 372

B.7 F: Options
No.
(Addr. Name
Hex)
F7-15 Communication Speed
(03F3) Selection
F7-16 Communication Loss
(03F4) Timeout
F7-17 EtherNet/IP Speed
(03F5) Scaling Factor
F7-18 EtherNet/IP Current
(03F6) Scaling Factor
F7-19 EtherNet/IP Torque
(03F7) Scaling Factor
F7-20 EtherNet/IP Power
(03F8) Scaling Factor
F7-21 EtherNet/IP Voltage
(03F9) Scaling Factor
F7-22 EtherNet/IP Time
(03FA) Scaling
F7-23 to
F7-32 Dynamic Output
(03FB to Assembly Parameters
0374)
F7-33 to
F7-42 Dynamic Input
(0375 to Assembly Parameters
037E)
<1> Parameter setting value is not reset to the default value when the drive is initialized.
<2> Values shown are for the MECHATROLINK-II option (SI-T3). Values for MECHATROLINK-III option (SI-ET3) are:
Min: 03
Max.: EF
<3> Values shown are for the MECHATROLINK-II option (SI-T3). Values for MECHATROLINK-III option (SI-ET3) are:
0: 64-byte
1: 32-byte
<4> Cycle power for setting changes to take effect.
<5> If F7-13 is set to 0, all IP addresses (F7-01 to F7-04) must be unique.
372
LCD Display
Baud Rate Sets the communication speed
10: 10 Mbps 10: 10 Mbps
100: 100 Mbps 100: 100 Mbps
Sets the timeout value for communication loss detection in
CommLoss Tout tenths of a second. A value of 0 disables the connection timeout.
Example: An entered value of 100 represents 10.0 seconds.
Sets the scaling factor for the speed monitor in EtherNet/IP
EN Speed Scale
Class ID 2AH Object.
Sets the scaling factor for the output current monitor in
EN Current Scale
EtherNet/IP Class ID 2AH Object.
Sets the scaling factor for the torque monitor in EtherNet/IP
EN Torque Scale
Class ID 2AH Object.
Sets the scaling factor for the power monitor in EtherNet/IP
EN Power Scale
Class ID 2AH Object.
Sets the scaling factor for the voltage monitor in EtherNet/IP
EN Voltage Scale
Class ID 2AH Object.
Sets the scaling factor for the time monitor in EtherNet/IP Class
EN Time Scale
ID 2AH Object.
Parameters used in Output Assembly 116. Each parameter
contains a MEMOBUS/Modbus address. The value received for
Output Assembly 116 will be written to this corresponding
–
MEMOBUS/Modbus address. A MEMOBUS/Modbus address
value of 0 means that the value received for Output Assembly
116 will not be written to any MEMOBUS/Modbus register.
Parameters used in Input Assembly 166. Each parameter
contains a MEMOBUS/Modbus address. The value sent for
Input Assembly 166 will be read from this corresponding
– MEMOBUS/Modbus address. A MEMOBUS/Modbus address
value of 0 means that the value sent for Input Assembly 166 is
not defined by the user, therefore the option default register
value will be returned.
Description
YASKAWA TOEP YAIP1W 01F YASKAWA AC Drive - iQpump1000 User Manual
Values Page
Default: 10
–
Range: 10, 100
Default: 0
Min.: 0 –
Max.: 300
Default: 0
Min.: -15 –
Max.: 15
Default: 0
Min.: -15 –
Max.: 15
Default: 0
Min.: -15 –
Max.: 15
Default: 0
Min.: -15 –
Max.: 15
Default: 0
Min.: -15 –
Max.: 15
Default: 0
Min.: -15 –
Max.: 15
Default: 0 –
Default: 0 –