YASKAWA iQpump1000 User Manual page 440

B.16 U: Monitors
No.
(Addr. Name
Hex)
U1-92
Pump Status
(0BA7)
U1-93 Total Setpoint
(0BA8) Compensation
U1-94
Motor Speed
(0BA9)
U1-96
PI Auxiliary Control
(0BAB)
Feedback Level
<6>
U1-97
Water Level
(0BAC)
U1-98
Suction Pressure
(0BAD)
U1-99
(0BAE)
Anti-No-Flow Timer
<7>
<1> Display is in the following units:
2A0004 to 2A0040, 4A0002 to 4A0023, and 5A0007 to 5A0017: 0.01 A units.
2A0056 to 2A0415, 4A0031 to 4A0675, and 5A0022 to 5A0242: 0.1 A units.
4A0930 and 4A1200: 1 A units.
<2> When reading the value of this monitor via MEMOBUS/Modbus, a value of 8192 is equal to 100% of the drive rated output current.
<3> Values shown are specific to 200 V class drives. Double the value for 400 V class drives. Multiply the value by 2.875 for 600 V class drives.
<4> The display resolution depends on the ND selection. This value has two decimal places (0.01 kW) if the drive is set for a maximum applicable
motor capacity up to and including 11 kW, and one decimal place (0.1 kW) if the maximum applicable motor capacity is higher than 11 kW.
<5> Available in drive software versions PRG: 8551 and later.
<6> Available in drive software versions PRG: 8552 and later. Not available in drive models 4A0930 and 4A1200.
<7> Monitor is available through the Quick Monitor screen.
u
U2: Fault Trace
No.
(Addr. Name
Hex)
U2-01
Current Fault
(0080)
U2-02
Previous Fault
(0081)
U2-03 Frequency Reference at
(0082) Previous Fault
U2-04 Output Frequency at
(0083) Previous Fault
U2-05 Output Current at
(0084) Previous Fault
440
LCD Display
Displays Pump Running Status.
Pump Status
Displays the total absolute Setpoint Compensation.
Total SP Comp.
Displays the absolute value of the output frequency (U1-02)
Motor Speed
converted to RPM.
Displays the PI Auxiliary Control Feedback Level (H3-oo =
PI Aux FB Level
27).
Displays the amount of water above the water level sensor.
Water Level
Displays the amount of suction pressure.
Suction Pressure
The Anti-No-Flow reduces the output frequency when this
ANF Timer
value reaches the P2-24 setting.
LCD Display
Displays the current fault.
Current Fault
Displays the previous fault.
Last Fault
Displays the frequency reference at the previous fault.
Frequency Ref
Displays the output frequency at the previous fault.
Output Freq
Displays the output current at the previous fault.
Output Current
Note:
Description
U1 - 92= 00000000
Description
The unit is expressed in 1 A for models 4A0930
and 4A1200.
YASKAWA TOEP YAIP1W 01F YASKAWA AC Drive - iQpump1000 User Manual
Analog
Output Level
1
Drive
1
Pump 2
1
Pump 3
No signal output
1
Pump 4
available
1
Pump 5
1
Pump 6
0
Not used
0
Not used
No signal output
available
No signal output
available
N/A
Full scale:
10 V = Q4-02
Full scale:
10 V = Q5-02
No signal output
available
Analog
Output Level
No signal output
available
No signal output
available
No signal output
available
No signal output
available
No signal output
available
Unit
–
dep. on
P1-02
1 RPM
Unit
dep. on
Q6-21
Res.
dep. on
Q6-22
0.1 ft.
0.1 PSI
or "Hg
0.1 s
Unit
–
–
0.01 Hz
0.01 Hz
<1> <2>