YASKAWA iQpump1000 User Manual page 224

4.7 Basic iQpump Setup and Application Preset Parameters
Setting
0 During run
1 Zero speed
2 Speed agree 1
3 User-set speed agree 1
4 Frequency detection 1
5 Frequency detection 2
6 Drive ready
7 DC bus undervoltage
8 During baseblock (N.O.)
9 Frequency reference source
A Run command source
A HAND Mode
B Torque detection 1 (N.O.)
C Frequency reference loss
<1>
Braking resistor fault
D
E Fault
F Through mode
10 Minor fault
11 Fault reset command active
12 Timer output
13 Speed agree 2
14 User-set speed agree 2
15 Frequency detection 3
16 Frequency detection 4
17 Torque detection 1 (N.C.)
18 Torque detection 2 (N.O.)
19 Torque detection 2 (N.C.)
1A During reverse
1B During baseblock (N.C.)
1E Restart enabled
1F Motor overload alarm (oL1)
20 Drive overheat pre-alarm (oH)
22 Mechanical weakening detection
2F Maintenance period
30 During torque limit
37 During frequency output
38 Drive enabled
39 Watt hour pulse output
3D During speed search
3E PID feedback low
3F PID feedback high
40 Auto Mode
42 Pressure Reached
43 2 Motor Alternate
4A During KEB Ride-Thru
4C During fast stop
<1> Not available in models 4A0930 and 4A1200.
<2> Not available in models 2A0169 to 2A0415 and 4A0088 to 4A1200.
224
Table 4.22 Multi-Function Digital Output Terminal Settings
Function Page Setting
– 4D oH Pre-alarm time limit
–
<2> Braking transistor fault (rr)
4E
–
<2>
Braking resistor overheat (oH)
4F
–
51 Sequence timer 1
–
52 Sequence timer 2
–
53 Sequence timer 3
–
54 Sequence timer 4
–
58 Underload detection
–
60 Internal cooling fan alarm
–
71 Secondary PI Feedback Low
–
72 Secondary PI Feedback High
–
80 Pump 2 Control
–
81 Pump 3 Control
–
82 Pump 4 Control
–
83 Pump 5 Control
–
84 Pump 6 Control
–
89 Output 1 Limit
–
8B Lube Pump or Digital Output Delay
–
8F Internal Fan On
–
91 Pump Fault
–
92 Transducer Loss
–
93 Setptoint Not Met
–
94 Loss of Prime
–
95 Volute Thermostat Fault
96 High Feedback
–
97 Low Feedback
–
98 Low Flow
–
99 Accum Level
–
9A High Flow
–
9B Low Water Level
–
9C Low Suction
–
9D High Suction
–
9E Low PI Aux Level
–
9F High PI Aux Level
225
A0 Water Loss/Suction Pressure/PI Aux Control
–
A1 Differential Detected
–
A2 Sleep Active
–
A3 Start Delay
–
A4 Pre-Charge
–
A5 Anti-Jam Active
–
A6 De-Scale Active
–
A7 Flow Rate Limit
225
A9 Thrust Mode
–
AA Utility Start Delay
–
100 to
Function 0 to AA with inverse output
1AA
–
YASKAWA TOEP YAIP1W 01F YASKAWA AC Drive - iQpump1000 User Manual
Function Page
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–