YASKAWA iQpump1000 User Manual page 223

Setting
7 Accel/decel time selection 1
8 Baseblock command (N.O.)
9 Baseblock command (N.C.)
A Accel/decel ramp hold
B Drive overheat alarm (oH2)
C Analog terminal input selection
F Through mode
10 Up command
11 Down command
12 Forward Jog
13 Reverse Jog
14 Fault reset
15 Fast Stop (N.O.)
17 Fast Stop (N.C.)
18 Timer function input
19 PID disable
1A Accel/decel time selection 2
1B Program lockout
1E Reference sample hold
20 to 2F Ext. pump fault
30 PID integral reset
31 PID integral hold
Multi-Step Speed
32
Reference 4
34 PID soft starter cancel
35 PID input level selection
Forward run command
40
(2-Wire sequence)
Reverse run command
41
(2-Wire sequence)
Run command
42
(2-Wire sequence 2)
FWD/REV command
43
(2-Wire sequence 2)
47 Node setup
51 Sequence Timer Disable
52 Sequence Timer Cancel
60 DC Injection Braking command
External Speed Search
61
command 1
<1> Available in drive software versions PRG: 8552 and later.
Not available in drive models 4A0930 and 4A1200.
n H2-01 to H2-03: Terminal M1-M2, M3-M4, and MD-ME-MF Function Selection
The drive has three multi-function output terminals.
H2-02, and H2-03.
No.
H2-01 Terminal M1-M2 Function Selection (relay)
H2-02 Terminal M3-M4 Function Selection (relay)
H2-03 Terminal MD-ME-MF Function Selection (relay)
<1> Default is F: Through Mode in drive software versions PRG: 8551 and earlier.
YASKAWA TOEP YAIP1W 01F YASKAWA AC Drive - iQpump1000 User Manual
Function
Table 4.22
Parameter Name
4.7 Basic iQpump Setup and Application Preset Parameters
Page Setting
– External Speed Search
62
command 2
–
63 Field weakening
–
65 KEB Ride-Thru 1 (N.C.)
–
66 KEB Ride-Thru 1 (N.O.)
–
67 Communications test mode
–
68 High Slip Braking (HSB)
–
6A Drive enable
–
73 Low City Press
–
75 Up 2 command
–
76 Down 2 command
–
7A KEB Ride-Thru 2 (N.C.)
–
7B KEB Ride-Thru 2 (N.O.)
–
80 HAND Mode
–
81 HAND Mode 2
–
<1>
PI Switch to Aux
82
–
83 Alternate Multi-Setpoint (Q1-02)
–
84 Alternate Multi-Setpoint (Q1-03)
–
85 Alternate Multi-Setpoint (Q1-04)
–
88 Volute-Thermostat Normally Open
–
89 Volute-Thermostat Normally Closed
–
8C Disable Pre-Charge
–
8D Multi Setpoint 1
–
8E Multi Setpoint 2
–
8F Low Water Level
–
90 High Water Level
92 Reset Accum
–
95 Remove Drive Disable
–
A8 Secondary PI Disable (N.O.)
A9 Secondary PI Disable (N.C.)
–
AA Secondary PI Inverse Operation
AB Secondary PI Integral Reset
–
AC Secondary PI Integral Hold
–
AD Select Secondary PI Parameters
–
AF Emergency Override Forward Run
–
B0 Emergency Override Reverse Run
–
–
lists the functions available for these terminals using H2-01,
Function
Setting Range
0 to 192 37: During Frequency Output
0 to 192
42: Pressure Reached
0 to 192
Page
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
4
Default
<1>
E: Fault
223