Front And Rear View - Ubex-Mmu-X200; Front View; Rear View - Lightware UBEX-MMU-X200 User Manual

 
     
2. Product Overview 2. Product Overview
2.3. Front and Rear View - UBEX-MMU-X200
2.3.1. Front View
UBEX-MMU-X200
1 Control Ethernet Front panel RJ45 connector for control and firmware upgrade purpose. The port
port 1 supports 100 Mbps Ethernet connection, auto-negotiation, and auto-MDI/MDIX.
See the details about the cable wiring in the
the concept of the operation in the
Status LEDs The LEDs give immediate feedback about the recent status of the device. See
2
the details about the operation of the LEDs in the
LCD screen LCD screen showing the most important settings and parameters in the front
3
panel menu. See the details the LCD menu operation in the
Menu Operation - MMU
Jog dial control Easy setting and menu navigation by the jog dial control. Keep dial and click
4
knob while getting feedback on the LCD. See the details the LCD menu operation in
the Front Panel LCD Menu Operation - MMU
5 Reset button Reboots the device (the same as disconnecting from the power source and
reconnecting again).
6 USB connector Function will be added by future firmware update.
Status LEDs
LIVE
blinking The device operates normally, the core software is running.
on Device initialization is in progress.
off The device is not powered or out of operation.
POWER
on The device is powered and ready to use.
off The device is not powered or out of operation.
Applied F-series endpoint firmware package: v1.5.4 | Applied R-series endpoint firmware package: v1.5.4 | Applied MMU firmware package: v1.3.3 | LDC software: v2.4.2b4
1 2 3
CONTROL
ETHERNET 1
Matrix Management Unit
Reset
5
Ethernet Connectors
Ethernet Interface section.
Status LEDs
chapter.
chapter.
series – Matrix Application Mode – User's Manual series – Matrix Application Mode – User's Manual
2.3.2. Rear View
4
Control USB
6
7 RS-232
connectors
section and
section below.
Control Ethernet
8
port 2
Front Panel LCD
Ethernet port
9
for UBEX
network
q SFP slot for
1 GbE SFP
module for
UBEX network
AC connector
w
9 q
7 8
2 pcs 3-pole Phoenix connectors for serial communication. The connectors are
for controlling the device and connection with third-party system controllers.
See more details about the pin assignment in the
about the cable wiring in the Serial Ports
operation in the Serial Interface section.
Rear panel RJ45 connector for control and firmware upgrade purpose. The port
supports 1 Gbps Ethernet connection, auto-negotiation, and auto-MDI/MDIX.
See the details about the cable wiring in the
the concept of the operation in the Ethernet Interface
RJ45 connector with 1 GbE support for connection to the UBEX network.
Connect the MMU and the L3 network switch by a CATx cable via the connector.
See the details about the cable wiring in the
Use one of the UBEX network connectors (RJ45 or SFP) only in the same time to avoid
the network loop.
Optical port slots for an 1 GbE SFP module for connection to the UBEX network.
Connect the MMU and the L3 network switch by LC fiber optical cable or DAC
cable. Ports can be used for either singlemode or multimode fiber optical
connections. See more details about the SFP interface in the
Interfaces section.
Use one of the UBEX network connectors (RJ45 or SFP) only in the same time to avoid
the network loop.
Standard IEC connector accepting 100-240 V, 50 or 60 Hz. See more details
about it in the AC Power Connection section.
24 24
w
RS-232 Connector section,
section, and the concept of the
Ethernet Connectors section and
section.
Ethernet Connectors section.
SFP / SFP+