Set The Operation Mode; Query The Mac Address Of The Device; Query The Firmware Package Version; Identify The Device - Lightware UBEX-MMU-X200 User Manual

 
     
9. Programmer's Reference 9. Programmer's Reference
9.6.4. Set the Operation Mode

ATTENTION! This operation always requires rebooting the endpoint device.

INFO: The setting is stored in the MMU.
The operation mode (transmitter, receiver, or transceiver) of the device can be changed based on the required
application.
Command and Response
SET•/SYS/ENDPOINTS/<UBEX_EP>.OperationMode=<operation_mode>
ç
pw•/SYS/ENDPOINTS/<UBEX_EP>.OperationMode=<operation_mode>
æ
Parameters
Parameter Parameter description
The operation mode of
<operation_mode>
the endpoint device
Example
ç SET /SYS/ENDPOINTS/UBEX0039A1.OperationMode=Receiver
æ pw /SYS/ENDPOINTS/UBEX0039A1.OperationMode=Receiver
9.6.5. Query the MAC Address of the Device
Command and Response #mac
ç GET•/SYS/ENDPOINTS/<UBEX_EP>.MacAddress
pr•/SYS/ENDPOINTS/<UBEX_EP>.MacAddress=<MAC_address>
æ
Example
ç GET /SYS/ENDPOINTS/UBEX0039A1.MacAddress
æ pr /SYS/ENDPOINTS/UBEX0039A1.MacAddress=A8:D2:36:00:39:DA
Applied F-series endpoint firmware package: v1.5.4 | Applied R-series endpoint firmware package: v1.5.4 | Applied MMU firmware package: v1.3.3 | LDC software: v2.4.2b4
series – Matrix Application Mode – User's Manual series – Matrix Application Mode – User's Manual
Value Value description
The endpoint device is set to
Transmitter Transmitter. See the details in the
Transmitter Mode section.
The endpoint device is set to Receiver.
Receiver See the details in the Receiver Mode
section.
The endpoint device is set to
Transceiver Transceiver. See the details in the
Transceiver Mode section.
9.6.6. Query the Firmware Package Version
Command and Response #firmwareversion
ç GET•/SYS/ENDPOINTS/<UBEX_EP>.PackageVersion
pr•/SYS/ENDPOINTS/<UBEX_EP>.PackageVersion=<version>
æ
Example
ç GET /SYS/ENDPOINTS/UBEX0039A1.PackageVersion
æ pr /SYS/ENDPOINTS/UBEX0039A1.PackageVersion=v1.5.0b8
9.6.7. Identify the Device
Calling the method results the blinking of the front
panel status LEDs for 10 seconds. This feature can
be used to help to identify the device itself in the
rack shelf.
Command and Response #identifyme
ç CALL•/SYS/ENDPOINTS/<UBEX_EP>:identifyMe()
æ mO•/SYS/ENDPOINTS/<UBEX_EP>:identifyMe
Example
ç CALL /SYS/ENDPOINTS/UBEX0039A1:identifyMe()
æ mO /SYS/ENDPOINTS/UBEX0039A1:identifyMe
9.6.8. Control Lock
Enable/disable the operation of the jog dial control knob.
Command and Response #controllock #new
SET•/SYS/ENDPOINTS/<UBEX_EP>/SETTINGS/UI.ControlLock=<parameter>
ç
pw•/SYS/ENDPOINTS/<UBEX_EP>/SETTINGS/UI.ControlLock=<parameter>
æ
Parameters
Parameter Parameter description
Lock/unlock of the jog dial
<parameter>
control knob
INFO:
There is no difference between the 1 and 2 mode in the operation point of view.
Example
ç SET /SYS/ENDPOINTS/UBEX0039A1/SETTINGS/UI.ControlLock=1
æ pw /SYS/ENDPOINTS/UBEX0039A1/SETTINGS/UI.ControlLock=1
138 138
Value Value description
0 The jog dial control knob is unlocked.
1 The jog dial control knob is locked.
The jog dial control knob is
2
ForceLocked.