Rear View - Umx-Tps-Tx100 Series - Lightware UMX-TPS-TX120 User Manual


  
2. Product Overview
2.2. Rear View - UMX-TPS-TX100 series
UMX-TPS-TX120
1 2
UMX-TPS-TX130
1 2
12V DC input 12V DC input for local powering. For more details see the
1
Connection section or see all the available
RS-232 3-pole Phoenix connector for controlling the device with LDC or third-party control
2
connector systems, or third-party device control. Pin assignment can be found in the
Connector section.
3 GPIO 8-pole Phoenix connector for configurable general purpose input/output ports. Pin
assignment can be found in the
4 Ethernet Locking RJ-45 connector for configuring the device using Lightware Device
Controller (LDC), or updating it using Lightware Device Updater (LDU). Any third-
party control system can use this port to control the device.
TPS OUT Locking RJ45 connector for HDBaseT
5
(PoE) cable distances can be found in the
Status LEDs The LEDs give feedback about the actual state of the device. See the details in the
6
Rear Panel LEDs
7 IR IN and 3-pole TRS connector, also known as 3.5 mm (1/8") jack plug for optional IR
OUT receiver (IR IN) and transmitter (IR OUT) connection. Pin assignments can be
found in the IR Connector
8 Audio2 input 5-pole Phoenix connector for balanced analog audio input. Pin assignment can
be found in the
9 DVI-I input DVI-I connector for analog / DVI / HDMI signals. Pin assignment can be found in
the DVI-I Connector
4 5 6 7
3 4 5 6 7 9
Powering Options.
GPIO - General Purpose Input/Output Ports
signal transmission. Maximum CATx
TM
Maximum Extension Distances
section.
section.
Analog Stereo Audio (Phoenix) section.
section.
Applied firmware packages: (UMX-TPS): v1.5.0b4 | (WP-UMX-TPS): v1.4.0b8 | (FP-UMX-TPS): v1.4.0b8 | LDC software: v2.5.6b2
UMX-TPS-TX100 series – User's Manual
UMX-TPS-TX140 / UMX-TPS-TX140-Plus
UMX-TPS-TX140K
12V DC input
1
RS-232
2
Locking 12V DC
connector
3 GPIO
RS-232
4 Ethernet
section.
5 TPS OUT
(PoE)
Status LEDs
6
section.
IR IN and
7
OUT
8 Audio2 input
9 DVI-I input
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
12V DC input for local powering. For more details see the
Connection section or see all the available Powering
3-pole Phoenix connector for controlling the device with LDC or third-party control
systems, or third-party device control. Pin assignment can be found in the
Connector section.
8-pole Phoenix connector for configurable general purpose input/output ports. Pin
assignment can be found in the GPIO - General Purpose Input/Output Ports
Locking RJ-45 connector for configuring the device using Lightware Device
Controller (LDC), or updating it using Lightware Device Updater (LDU). Any third-
party control system can use this port to control the device.
Locking RJ45 connector for HDBaseT TM signal transmission. Maximum CATx
cable distances can be found in the Maximum Extension Distances
The LEDs give feedback about the actual state of the device. See the details in the
Rear Panel LEDs section.
3-pole TRS connector, also known as 3.5 mm (1/8") jack plug for optional IR
receiver (IR IN) and transmitter (IR OUT) connection. Pin assignments can be
found in the IR Connector section.
5-pole Phoenix connector for balanced analog audio input. Pin assignment can
be found in the Analog Stereo Audio (Phoenix)
DVI-I connector for analog / DVI / HDMI signals. Pin assignment can be found in
the DVI-I Connector section.
17
9
9
Locking 12V DC
Options.
RS-232
section.
section.
section.