1. Manuals
  2. Brands
  3. HEIDENHAIN Manuals
  4. Other
  5. POSITIP 8000
  6. Operating instructions manual

HEIDENHAIN POSITIP 8000 Operating Instructions Manual

Hide thumbs Also See for POSITIP 8000:
Table of Contents

Advertisement

Quick Links

Download this manual
POSITIP 8000
Operating Instructions
Digital Readout
English (en)
09/2018

Advertisement

Table of Contents
loading

Related Manuals for HEIDENHAIN POSITIP 8000

Summary of Contents for HEIDENHAIN POSITIP 8000

  • Page 1 POSITIP 8000 Operating Instructions Digital Readout English (en) 09/2018...

  • Page 2: Table Of Contents

    18 Turning – Programming....................... 281 19 File management..........................293 20 Settings............................301 21 Service and maintenance......................359 22 What to do if ..........................367 23 Removal and disposal........................373 24 Specifications..........................375 25 Index...............................381 26 List of figures..........................384 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 3 Intended use............................30 Improper use............................31 Personnel qualification........................31 Obligations of the operating company....................32 General safety precautions......................... 32 2.7 .1 Symbols on the product......................32 2.7 .2 Electrical safety precautions....................33 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 4 Product overview..........................50 Connecting encoders........................... 52 Connecting touch probes........................53 Wiring switching inputs and outputs....................54 Connecting a printer..........................59 Connecting input devices........................60 Connecting a network peripheral.......................60 5.10 Connecting the line voltage........................61 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 5 Operating elements of the position display................88 6.9.2 Position display functions......................89 6.10 Status bar............................. 93 6.10.1 Operating elements of the status bar..................93 6.10.2 Adjusting settings in the quick access menu................94 6.10.3 Stopwatch..........................95 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 6 Adjusting the display......................135 7 .4.5 Defining error messages....................... 135 7 .4.6 Backing up and restoring OEM settings................139 7 .4.7 Configuring the unit for screenshots..................140 Back up settings..........................142 Back up user files..........................143 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 7 Performing the reference mark search after startup............. 147 8.2.3 Setting the language......................148 8.2.4 Changing the password......................148 Single steps for setup........................149 8.3.1 Basic settings.........................149 8.3.2 Preparing machining processes (optional)................164 Back up settings..........................174 Back up user files..........................175 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 8 Programming the row of holes..................... 194 9.9.6 Simulating the program run....................195 9.10 Machining a bolt hole circle and row of holes (Program run)............196 9.10.1 Opening the program......................196 9.10.2 Running the program......................197 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 9 12.2 Defining the upper limit for the spindle speed (in the Turning application mode)......223 12.3 Conducting the reference mark search....................224 12.4 Setting a position as preset......................225 12.5 Adding a tool............................226 12.6 Selecting a tool..........................227 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 10 14.3.1 Positioning..........................244 14.4 Executing blocks..........................245 14.5 Using the simulation window......................246 14.5.1 Depiction as contour view.....................247 14.6 Working with the positioning aid....................248 14.7 Applying the Scaling factor......................249 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 11 Aborting the program run...................... 264 16.2.4 Using the simulation window....................264 16.2.5 Applying the Scaling factor....................266 16.2.6 Setting the spindle speed......................266 16.3 Managing programs...........................267 16.3.1 Opening a program........................267 16.3.2 Closing a program........................267 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 12 17 .5.3 Saving a program........................279 17 .5.4 Saving the program under a new name................279 17 .5.5 Saving the program automatically..................279 17 .5.6 Deleting a program........................ 280 17.6 Running program blocks........................280 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 13 18.6 Running program blocks........................292 19 File management..........................293 19.1 Overview............................. 294 19.2 File types.............................295 19.3 Managing folders and files....................... 295 19.4 Opening and viewing files........................ 298 19.5 Exporting files............................ 299 19.6 Importing files............................ 300 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 14 Fundamentals of axis configuration..................322 20.6.2 Reference marks........................326 20.6.3 Information..........................327 20.6.4 Switching functions........................327 20.6.5 Inputs (Switching functions)....................328 20.6.6 Outputs (Switching functions)....................329 20.6.7 Overrides..........................329 20.6.8 Adding M functions....................... 330 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 15 20.7 .14 Program execution......................... 354 20.7 .15 Text database......................... 355 20.7 .16 Messages..........................355 20.7 .17 Configuring M functions......................356 20.7 .18 Documentation........................356 20.7 .19 Software options........................357 20.7 .20 Back up and restore (OEM area)................... 357 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 16 24.3 Product dimensions and mating dimensions................. 378 24.3.1 Product dimensions with Single-Pos stand................379 24.3.2 Product dimensions with Duo-Pos stand................379 24.3.3 Product dimensions with Multi-Pos stand................380 24.3.4 Product dimensions with Multi-Pos holder................380 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 17 Contents 25 Index...............................381 26 List of figures..........................384 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 19: Fundamentals

    Fundamentals...

  • Page 20: Overview

    Demo software for the product POSITIP 8000 Demo is software you can install on a computer independently of the device. POSITIP 8000 Demo helps you to become familiar with, try out or present the functions of the device. You can download the current version of the software here: www.heidenhain.de...

  • Page 21: Documentation On The Product

    If the ID numbers and indexes as well as the firmware versions match, the documentation is valid If the ID numbers and indexes do not match, so that the documentation is not valid, you will find the current documentation for the product at www.heidenhain.de. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 22: Notes On Reading The Documentation

    Would you like to see any changes made, or have you found any errors? We are continuously striving to improve our documentation for you. Please help us by sending your requests to the following e-mail address: userdoc@heidenhain.de HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 23: Storage And Distribution Of The Documentation

    These instructions must be read and observed by every person who performs any of the following tasks: Mounting Installation Commissioning and configuration Operation Programming Service, cleaning and maintenance Troubleshooting Removal and disposal HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 24: Target Groups According To User Types

    An Operator-type user cannot create additional users, but is allowed to edit various operator-specific settings, such as his name or the language. A user of the Operator group can be logged in automatically as soon as the product is switched HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 25: Contents Of The Chapters

    ... using the "MDI" mode of operation ... executing single blocks ... the "MDI" mode of operation ✓ ✓ 14 "Turning MDI mode" ... using the "MDI" mode of operation ... executing single blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 26 ... the technical data of the product ✓ ✓ ✓ 24 "Specifications" ... product dimensions and mating dimensions (drawings) This chapter enables accessing the content of these ✓ ✓ ✓ 25 "Index" instructions according to specific topics. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 27: Notes In This Documentation

    The behavior of the functions depends on the configurable machine settings The book symbol represents a cross reference to external documentation, e.g. the documentation of your machine tool builder or other supplier. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 28: Symbols And Fonts Used For Marking Text

    Identifies an item of a list Example: TTL interface EnDat interface Bold Identifies menus, displays and buttons Example: Tap Shut down The operating system shuts down Turn the power switch off HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 29: Safety

    Safety...

  • Page 30: Overview

    The products of the POSITIP 8000 series are advanced digital readouts for use on manually operated machine tools. In combination with linear and angle encoders, digital readouts of the POSITIP 8000 series return the position of the tool in more than one axis and provide further functions for operating the machine tool.

  • Page 31: Improper Use

    Safety | Improper use Improper use In particular, the products of the POSITIP 8000 series must not be used in the following applications: Use and storage outside the operating conditions specified in "Specifications" Outdoor use Use in potentially explosive atmospheres...

  • Page 32: Obligations Of The Operating Company

    Functional ground connection as per IEC/EN 60204-1. Observe the information on installation. Product seal. Breaking or removing the product seal will result in forfeiture of warranty and guarantee. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 33: Electrical Safety Precautions

    Damage to internal parts of the product! If you open the product, the warranty and the guarantee will be void. Never open the housing Only the product manufacturer is permitted to access the inside of the product HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 35: Transport And Storage

    Transport and storage...

  • Page 36: Overview

    Digital Readout POSITIP 8000 Installation Instructions Printed issue of the Installation Instructions in the currently available languages Single-Pos stand Stand for rigid mounting, inclination angle 20°, fixing hole pattern 100 mm x 100 mm HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 37: Accessories

    TS 248 touch probe Touch probe for probing 683112-xx a workpiece (for setting presets), radial cable outlet USB connecting cable USB connecting cable for 354770-xx connector type A to type B HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 38: In Case Of Damage In Transit

    Contact the distributor or machine manufacturer for replacement parts If damage occurred during transit: Keep the packaging materials for inspection Contact HEIDENHAIN or the machine manufacturer This applies also if damage occurred to requested replacement parts during transit. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 39: Repackaging And Storage

    Storage of the product Package the product as described above Observe the specified ambient conditions Further information: "Specifications", Page 375 Inspect the product for damage after any transport or longer storage times HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 41: Mounting

    Mounting...

  • Page 42: Overview

    Allen key, size 2.5 (Duo-Pos stand) Material for mounting on supporting surface The unit must be mounted to a stand or a holder to ensure the correct and intended use of the product. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 43: Mounting On Single-Pos Stand

    Route the cable from behind through the opening of the stand and then through the lateral openings to the connections Figure 2: Product mounted on Single-Pos Figure 3: Cable routing on Single-Pos stand stand Further information: "Product dimensions with Single-Pos stand", Page 379 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 44 Route the cable from behind through the two supports of the stand and then through the lateral openings to the connections Figure 4: Product mounted on Duo-Pos stand Figure 5: Cable routing on Duo-Pos stand Further information: "Product dimensions with Duo-Pos stand", Page 379 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 45: Mounting On Multi-Pos Stand

    Route the cable from behind through the two supports of the stand and then through the lateral openings to the connections Figure 6: Product mounted on Multi-Pos stand Figure 7: Cable routing on Multi-Pos stand Further information: "Product dimensions with Multi-Pos stand", Page 380 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 46: Mounting On Multi-Pos Holder

    Route the cable from behind through the two supports of the holder and then through the lateral openings to the connections Figure 8: Product mounted on Multi-Pos Figure 9: Cable routing on Multi-Pos holder holder Further information: "Product dimensions with Multi-Pos holder", Page 380 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 47: Installation

    Installation...

  • Page 48: Overview

    This chapter describes the Installation of the product. It contains information about the product's connections and instructions about how to correctly connect the peripheral devices. The following steps must be performed only by qualified personnel. Further information: "Personnel qualification", Page 31 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 49: General Information

    The incorrect wiring of inputs or outputs can cause damage to the unit or to peripheral devices. Comply with the pin layouts and specifications of the product Assign only pins or wires that will be used Further information: "Specifications", Page 375 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 50: Product Overview

    SN 12 345 678 www.heidenhain.de X32X33 X34 X116 X117 X100 AC 100 V ... 240 V 50 Hz .. 60 Hz (max. 38 W) Figure 10: Rear panel of devices with ID 1089176-xx HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 51 Figure 11: Rear panel of devices with ID 1089177-xx Connections: X102: 37-pin D-sub connection for digital TTL interface (8 inputs, 16 outputs) X112: 15-pin D-sub connection for touch probes (e.g. HEIDENHAIN touch probe) X1-X6: 15-pin D-sub connections for encoder with interfaces of the type 1 V 11μA or EnDat 2.2...

  • Page 52: Connecting Encoders

    If the cable connectors include mounting screws, do not overtighten them Pin layout of X1, X2, X3, X4, X5, X6 11 µA EnDat 2.2 R– 11 μA Inter- EnDat DATA shield CLOCK A– Sense Sense 11 μA EnDat DATA CLOCK HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 53: Connecting Touch Probes

    If the cable connectors include mounting screws, do not overtighten them Pin layout of X112 LED+ B 5 V B 12 V DC 12 V DC 5 V LED– B – Probe signals, readiness TP – Touch Probe, normally closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 54: Wiring Switching Inputs And Outputs

    "Product overview", Page 50 If the cable connectors include mounting screws, do not overtighten them The digital or analog inputs and outputs must be assigned in the device settings of the respective switching function. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 55 Dout 5 Dout 7 Dout 9 Dout 11 Dout 13 Dout 15 Digital inputs: Digital outputs: X102 X102 Pin 22 DC 5 V DC 5 V Dout 0...15 Din 0...7 GND (D) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 56 Installation | Wiring switching inputs and outputs Pin layout of X104 CO – Change Over NO – Normally Open NC – Normally Closed Relay outputs: HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 57 Dout 1 Dout 3 Dout 5 Dout 7 DC 24 V Digital inputs: Digital outputs: X105 X105 Pin 17, 18, 36 Din 0...23 DC 24 V DC 24 V Dout 0...7 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 58 Aout 0+ Aout 1+ Aout 2+ Aout 3+ Ain 1 Ain 3 Aout 0– Aout 1– Aout 2– Aout 3– DC 5 V Ain 0 Ain 2 Analog inputs: Analog outputs: HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 59: Connecting A Printer

    The cable connector must firmly engage in the port Further information: "Product overview", Page 50 Pin layout of X116 1 2 3 4 5 6 7 8 D1– D3– D2– D4– (TX+) (TX–) (RX+) (RX–) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 60: Connecting Input Devices

    The cable connector must firmly engage in the port Further information: "Product overview", Page 50 Pin layout of X116 1 2 3 4 5 6 7 8 D1– D3– D2– D4– (TX+) (TX–) (RX+) (RX–) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 61: Connecting The Line Voltage

    Comply with the pin layout Connect the power connection to a 3-wire grounded power outlet using a power cable that meets requirements Further information: "Product overview", Page 50 Pin layout X100 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 63: Basic Operation

    Basic operation...

  • Page 64: Overview

    Malfunctions of the touchscreen caused by humidity or contact with water! Humidity or water can impair the proper functioning of the touchscreen. Protect the touchscreen from humidity or contact with water Further information: "Product data", Page 376 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 65: Gestures And Mouse Actions

    Means pressing the left mouse button once and holding it down The actions initiated by holding are Quickly changing the values in input fields with plus and minus buttons HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 66 Means pressing the left mouse button once and holding it down while moving the mouse; at least the starting point of the motion is defined The actions initiated by dragging include Scrolling through lists and texts HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 67: General Operating Elements And Functions

    Tap + or – until the desired value is displayed Long-press + or – to scroll through the values more quickly The selected value is displayed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 68 The new feature is added Close Tap Close to close a dialog Confirm Tap Confirm to conclude an activity Back Tap Back to return to the higher level in the menu structure HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 69: Positip 8000 - Switch-On And Switch-Off

    Basic operation | POSITIP 8000 – switch-on and switch-off POSITIP 8000 – switch-on and switch-off 6.4.1 Switching on POSITIP 8000 Before using the product, you need to perform the commissioning and setup steps. Depending on the purpose of use, you may have to configure additional setup parameters.

  • Page 70: Switching Off Positip 8000

    Basic operation | POSITIP 8000 – switch-on and switch-off 6.4.3 Switching off POSITIP 8000 NOTICE Damage to the operating system! Disconnecting the power source while the product is on can damage the operating system of the product. Use the Switch-off menu to shut down the product...

  • Page 71: User Login

    The language selected for the user is indicated by a national flag in the Language drop-down list Select the flag for the desired language in the Language drop-down list The user interface is displayed in the selected language HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 72: Performing The Reference Mark Search After Startup

    "Activating the reference mark search", Page 115 User interface The unit is available in different versions, which are variously equipped. The user interface and available functions may vary depending on the version. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 73: User Interface After Switch-On

    Operator type, the Manual operation menu is displayed after the product has started up. Further information: "Manual operation menu", Page 76 If automatic user login is not active, the product opens the User login menu. Further information: "User login menu", Page 86 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 74: Main Menu Of The User Interface

    Program run Execution of a previously created program with operator guidance Further information: "Program run menu", Page 81 Programming Creation and management of individual programs Further information: "Programming menu", Page 82 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 75 Further information: "Settings menu ", Page 87 Switch-off Shutdown of the operating system or activation of energy- saving mode Further information: "Switch-off menu", Page 88 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 76: Manual Operation Menu

    The user interface for manual operation is displayed Manual operation menu (in the Milling application mode) Figure 15: Manual operation menu in the milling application mode Axis key Reference Position display Status bar Spindle speed (machine tool) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 77: Manual Operation Menu In The Turning Application Mode

    In the Manual operation menu, the workspace shows the position values measured at the machine axes. The status bar provides auxiliary functions. Further information: "Milling Manual operation", Page 211 Further information: "Turning Manual operation", Page 221 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 78: Mdi Menu

    Tap MDI in the main menu MDI mode menu (in the Milling application mode) Figure 17: MDI mode menu in the milling application mode Axis key Actual position Distance-to-go Status bar Spindle speed (machine tool) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 79: Mdi Mode Menu In The Turning Application Mode

    MDI mode menu (in the Turning application mode) Figure 18: MDI mode menu in the turning application mode Axis key Actual position Coupled axes Distance-to-go Status bar Spindle speed (machine tool) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 80: Mdi Block Dialog

    You specify the distance to the target point, and the distance to go is then calculated and displayed. The status bar provides additional measured values and functions. Further information: "Milling MDI mode", Page 229 Further information: "Turning MDI mode", Page 241 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 81: Program Run Menu

    The user interface for program run is displayed Program run menu (in the Milling application mode) Figure 20: Program run menu in the milling application mode View bar Status bar Program control Spindle speed (machine tool) Program management HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 82: Programming Menu

    Programming menu Activation Tap Programming in the main menu The user interface for programming is displayed The status bar and the optional OEM bar are not available in the Programming menu. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 83: Programming Menu In The Milling Application Mode

    You can display a visualization of the selected block in the optional simulation window. Figure 23: Programming menu with simulation window opened View bar Simulation window (optional) Block parameters Toolbar Program blocks Program management HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 84: Programming Menu In The Turning Application Mode

    You can display a visualization of the selected block in the optional simulation window. Figure 25: Programming menu with simulation window opened View bar Simulation window (optional) Block parameters Toolbar Program blocks Program management HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 85: File Management Menu

    The USB mass storage devices and the network drives are displayed with their names or drive designations. Further information: "File management", Page 293 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 86: User Login Menu

    To log in another user, the logged-in user must log out. Further information: "User login and logout", Page 70 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 87: Settings Menu

    Further information: "Settings", Page 301 The product provides various authorization levels that grant the user full or restricted access to management and operation functionality. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 88: Switch-Off Menu

    In the turning application mode: The position display shows the diameter of the radial machining axis X Further information: "Display", Page 305 Reference mark search performed successfully HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 89: Position Display Functions

    If the Z axis and the Zo axis have been coupled, the Program run operating mode is disabled. Coupling is identical for the Z axis and Zo axis. The following describes only the coupling of the Z axis. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 90 Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 91 If the desired spindle speed cannot be attained with the selected gear stage, then the gear stage icon will flash with an upward pointing arrow (higher gear stage) or with a downward pointing arrow (lower gear stage). HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 92 Enter the value for Maximum spindle speed Tap Confirm The speed mode is activated The spindle speed is shown in the unit of measure rpm Drag the S axis key to the left HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 93: Status Bar

    Display of the actual feed rate of the currently fastest axis The feed-rate value can be set in the Manual operation and MDI operating modes; tapping it opens the feed-rate menu HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 94: Adjusting Settings In The Quick Access Menu

    Tap the quick access menu on the status bar Select the desired option Tap Close to close the quick access menu If the Diameter option is selected, then the corresponding icon appears in the position display HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 95: Stopwatch

    Operating element Function Start Starts time measurement or resumes time measure- ment after Pause Pause Interrupts time measurement Stop Stops time measurement and resets it to 0:00:00 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 96: Calculator

    The speed is calculated automatically Taper calculator Turning Enter D1, D2, and L in the provided fields The angle is automatically calculated The taper is graphically displayed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 97: Auxiliary Functions In Manual Operation Mode

    For setting presets Further information: "Presetting by probing (in the Turning application mode)", Page 171 Tool data For tool setting (touch-off) Further information: "Setting the tool (in the Turning application mode)", Page 166 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 98: Oem Bar

    Spindle speed Displays one or more values that have been predefined for the spindle speed of a connected NC-controlled machine tool Further information: "Configuring nominal values for the spindle speed", Page 131 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 99: Calling Functions Of The Oem Bar

    Long-press the desired Spindle speed field on the OEM bar The background color of the field is highlighted in green The product applies the current spindle speed as the nominal value and displays it in the Spindle speed field HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 100: Messages And Audio Feedback

    To resize the message display area, drag the handle up or down To close the display area, drag the handle up out of the screen The number of unclosed messages is indicated in Messages HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 101 The message disappears To close a message that potentially has an effect on the application, tap OK If applicable, the message will now be taken into account by the application The message disappears HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 102: Wizard

    The available sounds are grouped into categories. The sounds differ within a category. You can define the audio feedback settings in the Settings menu. Further information: "Sounds", Page 309 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 103: Commissioning

    Commissioning...

  • Page 104: Overview

    If the password is no longer known, contact a HEIDENHAIN service agency. Confirm the entry with RET Tap Log in The user is logged in The product opens the Manual operation mode HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 105: Performing The Reference Mark Search After Startup

    The language selected for the user is indicated by a national flag in the Language drop-down list Select the flag for the desired language in the Language drop-down list The user interface is displayed in the selected language HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 106: Changing The Password

    Confirm entry with RET Enter the new password and repeat it Confirm entry with RET Tap OK Close the message with OK The new password is available the next time the user logs in HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 107: Steps For Commissioning

    Tap Settings in the main menu Tap Service Open in the sequence OEM area Settings Select the desired application mode in the Application drop- down list: Milling: Milling application mode Turning: Turning application mode HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 108: Basic Settings

    To set the rounding method, tap the corresponding drop- down list and select the rounding method To set the number of decimal places displayed, tap – or + Further information: "Units", Page 312 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 109 Contact a HEIDENHAIN service agency and submit the displayed device information in order to request a license key for the product The license key and the license file are generated and sent by e-mail HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 110 Activating a license key You can activate a license key by Reading the license key from the provided license file into the product Entering the license key manually into the product HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 111 On the overview page, you can check which Software options are enabled for the product. Tap Settings in the main menu Tap Service Open in the sequence Software options Overview A list of enabled Software options is displayed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 112: Configuring The Axes

    You have to configure the inputs and outputs, as well as further parameters Further information: "Spindle axis S", Page 341 For the parameters of HEIDENHAIN encoders that are typically connected to the product, refer to the overview of typical encoders. Further information: "Overview of typical encoders", Page 118...
  • Page 113 Mechanical ratio Tap Reference point displacement Use the ON/OFF slide switch to activate or deactivate Reference point displacement (calculation of the offset between the reference mark and the machine zero point) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 114 To switch to the previous display, tap Back To view the electronic ID label of the encoder, tap Identification label To view the results of encoder diagnostics, tap Diagnosis Further information: "Axes X, Y ...", Page 331 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 115 The functions of the product will only be available after the reference mark search has been completed The Reference symbol stops blinking upon successful completion of the reference mark search Further information: "Operating elements of the position display", Page 88 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 116 Tap Reference marks Select the reference mark in the Reference mark drop-down list: None: There is no reference mark One: The encoder has one reference mark Coded: The encoder has distance-coded reference marks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 117 Positive: The direction of traverse is in the counting direction of the encoder Negative: The direction of traverse is opposite to the counting direction of the encoder Further information: "Axes X, Y ...", Page 331 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 118 Commissioning | Steps for commissioning Overview of typical encoders The following overview lists the parameters of the HEIDENHAIN encoders that are typically connected to the product. When connecting other encoders, refer to the encoder's documentation for the required parameters. Linear encoders...
  • Page 119 If applicable, enter the corresponding values in the fields Maximum spindle speed for oriented spindle stop and Maximum spindle speed for thread cutting Further information: "Spindle axis S", Page 341 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 120 This results in the minimum configuration for the outputs and inputs: Analog output Inputs Control of the spindle axis Spindle start Spindle stop Manually Assigned Assigned Assigned M functions Assigned Not connected Not connected M3/M4 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 121 For all methods, the actual error curve must be exactly measured (e.g., with the help of a comparator measuring device or calibration standard). Linear error compensation and segmented linear error compensation cannot be combined with each other. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 122 Activate Compensation with the ON/OFF sliding switch You can also use Linear error compensation (LEC) for angle encoders if the rotation angle is less than 360°. Further information: "Linear error compensation (LEC)", Page 337 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 123 To switch to the previous display, tap Back twice Activate Compensation with the ON/OFF sliding switch The error compensation for the axis is applied Further information: "Segmented linear error compensation (SLEC)", Page 338 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 124 To switch to the previous display, tap Back Activate Compensation with the ON/OFF sliding switch The adjusted error compensation for the axis is applied Further information: "Segmented linear error compensation (SLEC)", Page 338 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 125: Using M Functions

    The product also supports manufacturer-specific M functions with the following characteristics: Number range definable from M100 to M120 Function depends on the machine manufacturer Use in the button of the OEM bar Further information: "Configuring the OEM bar", Page 130 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 126: Configuring A Touch Probe (In The Milling Application Mode)

    The following information applies only to the Milling application mode. You can use probing functions to set presets with a HEIDENHAIN KT 130 Edge Finder. The stylus of the edge finder can be additionally fitted with a ruby ball tip.

  • Page 127: Oem Area

    Tap the file name Tap Select The file is copied to the unit’s Service info area Further information: "Service info", Page 313 Confirm the successful transfer with OK Further information: "Documentation", Page 356 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 128: Adding A Startup Screen

    Tap the file name Tap Select The graphic file is copied to the product and displayed as the startup screen the next time the product is started Confirm the successful transfer with OK HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 129 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 130: Configuring The Oem Bar

    "Logo OEM bar item", Page 351 Navigate to the folder containing the image file, and select the file Tap Select Select the desired option in the Link to documentation drop- down list HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 131 Confirm the entry with RET Tap Spindle speed in the Type drop-down list Tap the name of the spindle in the Spindle drop-down list Enter the desired nominal value into the Spindle speed input field HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 132 For every M function, you can also define corresponding images for displaying the status using Select image for active function and Select image for inactive function Further information: "M function OEM bar item", Page 352 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 133 For each special function, you can also define corresponding images for displaying the status using Select image for active function and Select image for inactive function Further information: "Special functions OEM bar item", Page 353 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 134 Open in the sequence OEM area OEM bar Bar items Tap the desired menu item Tap Remove bar entry Tap OK to confirm deletion The menu item is deleted from the OEM bar HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 135: Adjusting The Display

    As an OEM, you can define specific error messages that overwrite standard error messages or are triggered by defined input signals as additional messages. For this purpose, you can create a text database that contains your specific error messages. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 136 Figure 31: Example – XML file for text database Then you import the XML file by means of a USB mass storage device (FAT32 format) into the product and save it, for example, to the Internal/Oem storage location. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 137 Navigate to the folder containing the XML file Tap the file name Tap Select Confirm the successful transfer with OK You have now successfully imported the Text database Further information: "Text database", Page 355 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 138 Tap Settings in the main menu. Tap Service Open in the sequence OEM area Settings Messages Tap the desired message entry Tap Remove the entry Tap OK to confirm deletion The error message is deleted HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 139: Backing Up And Restoring Oem Settings

    If required, connect a USB mass storage device (FAT32 format) to a USB port of the product Navigate to the folder containing the backup file Select the backup file Tap Select Confirm the successful transfer with OK HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 140: Configuring The Unit For Screenshots

    Demo. For a detailed description, please refer to the POSITIP 8000 Demo User’s Manual contained in the download folder of the software. Further information: "Demo software for the product", Page 20 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 141 Remote access for screenshots on the product. Tap Settings in the main menu Tap Service Tap OEM area Activate Remote access for screenshots with the ON/OFF sliding switch Further information: "OEM area", Page 349 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 142: Back Up Settings

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 143: Back Up User Files

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 145: Setup

    Setup...

  • Page 146: Overview

    Make sure that you have read and understood the "Basic operation" chapter before carrying out the actions described below. Further information: "Basic operation", Page 63 The following steps must be performed only by qualified personnel. Further information: "Personnel qualification", Page 31 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 147: Logging In For Setup

    The Reference symbol stops blinking upon successful completion of the reference mark search Further information: "Operating elements of the position display", Page 88 Further information: "Activating the reference mark search", Page 115 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 148: Setting The Language

    Confirm entry with RET Enter the new password and repeat it Confirm entry with RET Tap OK Close the message with OK The new password is available the next time the user logs in HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 149: Single Steps For Setup

    To set the rounding method, tap the corresponding drop- down list and select the rounding method To set the number of decimal places displayed, tap – or + Further information: "Units", Page 312 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 150 Use the ON/OFF sliding switch to show or hide the contents Tap OK A message appears Close the message with OK The user is created with the basic data. The user can then further edit the data himself later HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 151 Close the message with OK To change the language, select the flag for the desired language in the Language drop-down list To activate or deactivate Auto login, use the ON/OFF sliding switch HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 152 Tap Settings in the main menu Tap User Tap the user you want to delete Tap Remove user account Enter the password of the authorized user (OEM or Setup) Tap OK The user is deleted HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 153 The Operating Instructions are copied to the product Any existing Operating Instructions will be overwritten Confirm successful transfer with OK The Operating Instructions can be opened and displayed on the product HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 154 Confirm the entires with RET Enter the Preferred DNS server and, if required, the Alternative DNS server Confirm the entires with RET The configuration of the network connection is applied Further information: "Network", Page 315 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 155 If this list contains the used printer, the appropriate driver is available on the product and you can directly configure the printer. If this is not the case, you will need a printer-specific PPD file. Further information: "Finding PPD files", Page 160 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 156 If the appropriate driver is not listed, a suitable PPD file must be copied to the product. Further information: "Finding PPD files", Page 160 The driver is activated Tap Close in the message HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 157 Use the CUPS web interface to configure the enhanced settings of the connected printer. You can also use this web interface if the printer information fails over the product. Further information: "Using CUPS", Page 161 Further information: "Printers", Page 309 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 158 Further information: "Finding PPD files", Page 160 The driver is activated Tap Close in the message Tap Set standard values Tap Resolution to set the printer resolution HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 159 Use the CUPS web interface to configure the enhanced settings of the connected printer. You can also use this web interface if the printer information fails over the product. Further information: "Using CUPS", Page 161 Further information: "Printers", Page 309 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 160 Select the PPD file Tap Select The PPD file is copied to the product Tap Continue The PPD file is loaded and the driver is activated Tap Close in the message HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 161 (e.g. http://10.6.225.86:631) In the web interface, click on the Administration tab and select the desired action See the Online Help tab for detailed information about the CUPS web interface. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 162 In the Printers drop-down list, select the printer you no longer need The model, location and connection of the printer are displayed Tap Remove Confirm with OK The printer is removed from the list and can no longer be used HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 163 Tap Input devices Select the flag for the desired language in the USB keyboard layout drop-down list The keyboard assignment corresponds to the selected language Further information: "Input devices", Page 308 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 164: Preparing Machining Processes (Optional)

    You can save a maximum of 99 tools in the tool table. Figure 33: Tool table with tool parameters in the Milling appli- cation mode Tool type Tool diameter Tool length Edit tool table HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 165 To protect the entry for a tool from accidental changes or deletion, tap the Lock symbol next to the tool's entry The symbol changes and the entry is locked Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 166 To add a new tool, enter a number that has not yet been assigned in the tool table and confirm by pressing RET Tap Confirm in the wizard The probed coordinates are adopted for the tool HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 167 The symbol changes and the entry is unlocked Tap Delete A message appears Close the message with OK The selected tool is deleted from the tool table Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 168 Milling Numerical You must manually enter the numeric value of input the preset in the preset table Turning Depending on the application, users of the type Operator define the presets. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 169 Determine the centerline of a workpiece (two probing procedures) Determine the center point of a circular form (hole or cylinder) (three probing procedures with tool, four probing procedures with edge finder) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 170 Leave the input field empty to load the measured value To define a new value, enter the desired value Confirm the entry with RET Tap Confirm in the wizard The probed coordinate is loaded as preset HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 171 To create a new preset, enter a number that has not yet been assigned in the preset table and confirm with RET Tap Confirm in the wizard The probed coordinates are adopted as a preset HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 172 To protect the entry for a preset from accidental changes or deletion, tap the Lock symbol next to the preset's entry The symbol changes and the entry is locked Tap Close The Preset table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 173 The symbol changes and the entry is unlocked Tap Delete A message appears Close the message with OK The selected preset(s) is/are deleted from the preset table Tap Close The Preset table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 174: Back Up Settings

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 175: Back Up User Files

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 177: Milling - Quick Start

    Milling – Quick Start...

  • Page 178: Overview

    "Milling Manual operation", "Milling MDI mode", "Milling Programming" and "Milling Program run". Make sure that you have read and understood the "Basic operation" chapter before carrying out the actions described below. Further information: "Basic operation", Page 63 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 179: Logging In For Quick Start

    Setup user or OEM user for the assigned password. If the password is no longer known, contact a HEIDENHAIN service agency. Confirm entry with RET Tap Log in HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 180: Requirements

    A pre-processed workpiece blank is clamped on the machine tool Product A spindle axis is configured The axes have been homed Further information: "Conducting the reference mark search", Page 213 A HEIDENHAINKT 130 Edge Finder is available HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 181 The defined Ø 5.0 mm drill is added to the tool table Repeat the sequence for the other tools using the naming convention [type] [diameter] Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 182: Determining The Preset (Manual Operation Mode)

    RET Tap Confirm in the wizard The probed coordinate is loaded in preset 0 Repeat the procedure and define the preset in the Y direction via probing HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 183: Machining A Through Hole (Manual Operation Mode)

    On the machine tool move the spindles as follows: X direction: 95 mm Y direction: 50 mm Predrill the through hole and retract the spindle Keep positions X and Y You have successfully predrilled the through hole HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 184: Boring The Through Hole

    The associated tool parameters are applied automatically The Tools dialog is closed On the product, set a spindle speed of 400 rpm Bore the through hole and retract the spindle You have successfully bored the through hole HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 185: Machining A Rectangular Pocket (Mdi Mode Of Operation)

    Figure 39: Example workpiece – machining a rectangular pocket Activation Tap MDI in the main menu The user interface for the MDI mode is displayed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 186: Defining The Rectangular Pocket

    Feed rate for plunging: 260 Confirm each entry with RET To run the block, tap END The positioning aid is displayed If the simulation window is active, the rectangular pocket is visualized HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 187: Milling A Rectangular Pocket

    Start the machining process—follow the instructions of the wizard The product executes the individual steps of the milling operation Tap Close Program run is terminated The wizard closes You have successfully machined the rectangular pocket HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 188: Machining A Fit (Mdi Mode Of Operation)

    Z coordinate: –25 Confirm each entry with RET To run the block, tap END The positioning aid is displayed If the simulation window is active, the position and traverse path are visualized HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 189: Reaming The Fit

    On the product, set a spindle speed of 250 rpm Start the machining process—follow the instructions of the wizard Tap Close Program run is terminated The wizard closes You have successfully machined the fit HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 190: Determining The Preset (Manual Operation Mode)

    To align the bolt hole circle and frame of holes you must set the circle center of the fit as the preset. Based on this preset the product then calculates all values for the relative coordinate system. Ascertain the preset with the HEIDENHAIN KT 130 Edge Finder.
  • Page 191 Activating the preset Tap Presets on the status bar The Presets dialog box opens Tap preset 1 Tap Confirm The preset is set On the status bar is displayed with preset HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 192: Programming A Bolt Hole Circle And Row Of Holes (Programming)

    In Name enter the name Example Confirm the entry with RET In Unit for linear values select the mm unit of measure The program has been successfully created; you can then begin with programming HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 193: Programming The Tool

    Feed rate: 2000 Feed rate for plunging: 600 Confirm each entry with RET Tap END to terminate the input process Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 194: Programming The Tool

    If the tool axis is NC-controlled, additionally enter the following parameters: Clearance height: 10 Feed rate: 2000 Feed rate for plunging: 600 Confirm each entry with RET Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 195: Simulating The Program Run

    Check the view for programming errors, e.g. tool path intersections of holes If there are no programming errors you can machine the bolt hole circle and row of holes HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 196: Machining A Bolt Hole Circle And Row Of Holes (Program Run)

    Tap Open program in the program management A dialog box is opened. Select the Internal/Programs storage location in the dialog Tap the file Example.i Tap Open The selected program is opened HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 197: Running The Program

    Repeat the process for the row of holes machining block After drilling the row of holes tap Close The machining is terminated The program is reset The wizard is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 199: Turning - Quick Start

    Turning – Quick Start...

  • Page 200: Overview

    Setup user or OEM user for the assigned password. If the password is no longer known, contact a HEIDENHAIN service agency. Confirm entry with RET Tap Log in HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 201: Requirements

    The axes have been homed Further information: "Conducting the reference mark search", Page 213 Tools The following tools are available: Roughing tool Finishing tool Recessing tool (1 mm) Turning chisel (45°) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 202 Enter the value Confirm the entry with RET The defined finishing tool is added to the tool table Repeat this process for the other tools Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 203: Setting Up The Lathe

    The Zo axis is now coupled with the Z axis The icon for the coupled axes is shown next to the Z axis key The position value for the coupled axes is shown as a sum HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 204: Measuring The Reference Tool

    Enter the measured value in the X input field Tap Confirm in the wizard The Select the tool dialog appears Tap Finishing tool Tap Confirm in the wizard The parameters are adopted in the tool table HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 205: Tool Measurement

    Tap Confirm in the wizard The Select the tool dialog appears Tap roughing tool Tap Confirm in the wizard The parameters are added to the tool table Repeat this process for the other tools HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 206: Finding The Preset

    In the Z input field, enter the value Tap Confirm in the wizard The Select preset dialog appears in the Selected preset input field Select preset Tap Confirm in the wizard The probed coordinate is loaded as preset HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 207: Roughing The Outside Contour

    Z: 0.2 mm Move the tool into position on the lathe: X: 25.0 mm Retract the tool to a safe position Spindle OFF You have now successfully roughed the outside contour HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 208: Turning The Recesses

    Move the tool into position on the lathe: X: 21.0 mm Retract the tool to a safe position Repeat the procedure for the second recess Switch off the spindle You have successfully machined the recesses HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 209: Finishing The Outside Contour

    Move the tool into position on the lathe: X: 19.5 mm Move the tool into position on the lathe: Z: 0.0 mm Move the tool into position on the lathe: X: 25.0 mm HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 210 Turning – Quick Start | Finishing the outside contour Retract the tool to a safe position Spindle OFF You have now successfully finish turned the outside contour HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 211: Milling - Manual Operation

    Milling – Manual operation...

  • Page 212: Overview

    Tap Manual operation in the main menu The user interface for manual operation is displayed Figure 53: Manual operation menu Axis key Reference Position display Status bar Spindle speed (machine tool) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 213: Conducting The Reference Mark Search

    Tap Reference marks Existing reference marks are cleared The Reference symbol blinks Follow the instructions of the wizard The Reference symbol stops blinking upon successful completion of the reference mark search HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 214: Defining Presets

    You can define presets on a workpiece in the Manual Operation mode in the following ways: Probe a workpiece with a HEIDENHAIN KT 130 Edge Finder. Use this method to automatically enter the presets into the preset table. Probing a workpiece with a tool (touch-off). Use this method to define the respective tool position as a datum.

  • Page 215: Functions For The Probing Of Presets (In The Milling Application Mode)

    Determine the centerline of a workpiece (two probing procedures) Determine the center point of a circular form (hole or cylinder) (three probing procedures with tool, four probing procedures with edge finder) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 216: Presetting By Probing (In The Milling Application Mode)

    Leave the input field empty to load the measured value To define a new value, enter the desired value Confirm the entry with RET Tap Confirm in the wizard The probed coordinate is loaded as preset HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 217: Setting A Position As Preset

    The entered position value is linked with the current position and overwrites the active preset in the preset table The active preset is applied as the new value Perform the desired machining operation HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 218: Creating A Tool

    To protect the entry for a tool from accidental changes or deletion, tap the Lock symbol next to the tool's entry The symbol changes and the entry is locked Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 219: Selecting A Tool

    Tap the tool you want to use Tap Confirm The associated tool parameters are applied automatically The selected tool is shown on the status bar Mount the desired tool on the machine tool HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 221: Turning - Manual Operation

    Turning – Manual operation...

  • Page 222: Overview

    Manual operation mode. Activation Tap Manual operation in the main menu The user interface for manual operation is displayed Axis key Reference Position display Status bar Spindle speed (machine tool) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 223: Defining The Upper Limit For The Spindle Speed (In The Turning Application Mode)

    Enter the upper limit for the spindle speed with respect to the currently used clamping equipment. Confirm the entry with RET Tap Confirm The upper limit is now adopted by the unit The Upper limit for spindle speed dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 224: Conducting The Reference Mark Search

    Tap Reference marks Existing reference marks are cleared The Reference symbol blinks Follow the instructions of the wizard The Reference symbol stops blinking upon successful completion of the reference mark search HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 225: Setting A Position As Preset

    The entered position value is linked with the current position and overwrites the active preset in the preset table The active preset is applied as the new value Perform the desired machining operation HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 226: Adding A Tool

    To protect the entry for a tool from accidental changes or deletion, tap the Lock symbol next to the tool's entry The symbol changes and the entry is locked Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 227: Selecting A Tool

    Tap the tool you want to use Tap Confirm The associated tool parameters are applied automatically The selected tool is shown on the status bar Mount the desired tool on the machine tool HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 229: Milling - Mdi Mode

    Milling – MDI mode...

  • Page 230: Overview

    Tap MDI in the main menu Tap Create on the status bar The user interface for the MDI mode is displayed Figure 55: MDI menu View bar Block parameters MDI block Status bar Block tools HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 231: Block Types

    Select the tool on the status bar Further information: "Creating a tool table", Page 164 You can load the current axis position with Actual position capture into the appropriate input fields. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 232 Z axis) Feed rate Traversing speed of the tool axis (only for NC-controlled Z axis) Feed rate for Traversing speed of the tool axis for plunging (only for plunging NC-controlled Z axis) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 233 Frame of holes Clearance height Starting depth for milling in the tool axis (only for NC- controlled Z axis) Feed rate Traversing speed of the tool axis (only for NC-controlled Z axis) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 234 Length of the rectangular pocket in the X-axis direction Side length in Y Length of the rectangular pocket in the Y-axis direction Direction Direction in which the rectangular pocket is roughed out (clockwise or counterclockwise) Default: counterclockwise HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 235: Executing Blocks

    User intervention may be required, depending on the block; the wizard will display the relevant instructions Follow the instructions of the wizard If the product or the machine tool has NC-controlled axes, tap or press the NC START key HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 236: Using The Simulation Window

    Display of simulation and blocks Graphic-Position Display of simulation, parameters (position values for program run, if required) and blocks Position Display of parameters (position values for program run, if required) and blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 237: Depiction As Contour View

    The contour view uses the following colors (defaults): Figure 60: Simulation window with contour view Machining pattern (white) Current block or machining position (green) Tool contour, tool position and tool path (orange) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 238: Working With The Positioning Aid

    ± 5 mm of the nominal position. The color also changes in the following way: Display of positioning aid Meaning The tool center is moving away from the nominal positions Green The tool center is moving toward the nominal position HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 239: Applying The Scaling Factor

    The following MDI block is programmed: Figure 62: Example – MDI block A Scaling factor of -0.5 is activated for the X axis. The following MDI block will therefore be executed: HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 240: Example - Execution Of An Mdi Block With Scaling Factor

    Figure 63: Example – Execution of an MDI block with scaling factor If the calculated dimensions cannot be attained with the selected tool, the execution of the block is aborted. The scaling factor cannot be changed during execution of a block. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 241: Turning - Mdi Mode

    Turning – MDI mode...

  • Page 242: Overview

    Tap MDI in the main menu Tap Create on the status bar The user interface for the MDI mode is displayed Figure 64: MDI menu View bar Block parameters MDI block Status bar Block tools HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 243: Defining The Upper Limit For The Spindle Speed (In The Turning Application Mode)

    Enter the upper limit for the spindle speed with respect to the currently used clamping equipment. Confirm the entry with RET Tap Confirm The upper limit is now adopted by the unit The Upper limit for spindle speed dialog is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 244: Block Types

    You can load the current axis position with Actual position capture into the appropriate input fields. The following parameters are available: Positioning block Parameter Description Incremental position value, i.e. the position value is referenced to the actual position HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 245: Executing Blocks

    If the product or the machine tool has NC-controlled axes, tap or press the NC START key With multi-step blocks, such as machining patterns, tap Next to proceed to the next step in the wizard HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 246: Using The Simulation Window

    Display of simulation and blocks Graphic-Position Display of simulation, parameters (position values for program run, if required) and blocks Position Display of parameters (position values for program run, if required) and blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 247: Depiction As Contour View

    The simulation window for the currently selected block appears Tap Graphic on the view bar to enlarge the simulation window The parameter view is hidden and the simulation window is enlarged HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 248: Working With The Positioning Aid

    ± 5 mm of the nominal position. The color also changes in the following way: Display of positioning aid Meaning The tool center is moving away from the nominal positions Green The tool center is moving toward the nominal position HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 249: Applying The Scaling Factor

    The following MDI block is programmed: Figure 69: Example – MDI block A Scaling factor of -0.5 is activated for the X axis. The following MDI block will therefore be executed: HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 250: Example - Execution Of An Mdi Block With Scaling Factor

    Figure 70: Example – Execution of an MDI block with scaling factor If the calculated dimensions cannot be attained with the selected tool, the execution of the block is aborted. The scaling factor cannot be changed during execution of a block. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 251: Milling - Program Run

    Milling – Program...

  • Page 252: Overview

    Executing the Program Run depends on the machine tool and the product version: If the machine tool has NC-controlled axes and the product uses the POSITIP 8000 NC1 software option, the parameters for positioning movements are transferred directly to the machine tool.

  • Page 253: Using The Program

    "Managing programs", Page 258 Figure 71: Example of a program in the Program run operating mode View bar Simulation window (optional) Distance-to-go display Toolbar Program blocks Spindle speed (machine tool) Program management HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 254: Running The Program

    Milling – Program run | Using the program 15.2.1 Running the program With NC-controlled axes and software option POSITIP 8000 NC1 Press the NC START key on the machine tool The product selects the first block of the program Press the NC START key on the machine tool again User intervention may be required, depending on the block.

  • Page 255: Proceeding To A Specific Program Block

    The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Graphic-Position Display of simulation, position values and blocks Position Display of position values and blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 256 Current block or machining position (green) Tool contour, tool position and tool path (orange) You can modify the colors and line thicknesses used in the contour view. Further information: "Simulation window", Page 307 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 257: Applying The Scaling Factor

    Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 258: Managing Programs

    Tap the folder containing the file Tap the file Tap Open The selected program is loaded 15.3.2 Closing a program Tap Close program in the program management The opened program is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 259: Turning - Program Run

    Turning – Program...

  • Page 260: Overview

    Executing the Program Run depends on the machine tool and the product version: If the machine tool has NC-controlled axes and the product uses the POSITIP 8000 NC1 software option, the parameters for positioning movements are transferred directly to the machine tool.
  • Page 261 The user interface for program run is displayed View bar Status bar Program control Spindle speed (machine tool) Program management If the Z axis and the Zo axis have been coupled, the Program run operating mode is disabled. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 262: Using The Program

    "Managing programs", Page 258 Figure 73: Example of a program in the Program run operating mode View bar Simulation window (optional) Distance-to-go display Toolbar Program blocks Spindle speed (machine tool) Program management HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 263: Running The Program

    Turning – Program run | Using the program 16.2.1 Running the program With NC-controlled axes and software option POSITIP 8000 NC1 Press the NC START key on the machine tool The product selects the first block of the program Press the NC START key on the machine tool again User intervention may be required, depending on the block.

  • Page 264: Proceeding To A Specific Program Block

    The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Graphic-Position Display of simulation, position values and blocks Position Display of position values and blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 265 Current block or machining position (green) Tool contour, tool position and tool track (orange) You can modify the colors and line thicknesses used in the contour view. Further information: "Simulation window", Page 307 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 266: Applying The Scaling Factor

    Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 267: Managing Programs

    Tap the folder containing the file Tap the file Tap Open The selected program is loaded 16.3.2 Closing a program Tap Close program in the program management The opened program is closed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 269: Milling - Programming

    Milling – Programming...

  • Page 270: Overview

    The user interface for programming is displayed Figure 75: Programming menu View bar Toolbar Program management The status bar and the optional OEM bar are not available in the Programming menu. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 271: Block Types

    (inside contour) Incremental position value, i.e. the position value is referenced to the actual position Drilling through without position value specification (only for manually operated Z axis) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 272: Coordinate Systems

    M function Number of the M function Optional: Selection from function table Dwell time Time interval between machining steps HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 273: Machining Patterns

    Select the tool on the status bar Further information: "Creating a tool table", Page 164 You can load the current axis position with Actual position capture into the appropriate input fields. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 274: Creating A Program

    Further information: "Using the simulation window", Page 236 All changes to a program can be automatically saved. Tap Save program automatically in the program management All changes will be automatically saved immediately HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 275: Creating A Program Header

    The selected blocks are deleted from the program Tap Delete on the toolbar again 17.3.5 Saving a program Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 276: Using The Simulation Window

    The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Graphic-Position Display of simulation, position values and blocks Position Display of position values and blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 277: Depiction As Contour View

    The contour view uses the following colors (defaults): Figure 77: Simulation window with contour view Machining pattern (white) Current block or machining position (green) Tool contour, tool position and tool path (orange) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 278: Activating The Simulation Window

    Tap each program block, one after the other The program steps are displayed in the simulation window; you can enlarge the detail view as needed Tap Detail view to enlarge Tap Overview to show the overall view HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 279: Managing Programs

    The name of the program is displayed on the toolbar 17.5.5 Saving the program automatically Tap Save program automatically in the program management All changes to the program will be automatically saved immediately HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 280: Deleting A Program

    The parameters of the selected block are displayed Edit the relevant parameters, depending on the block type Confirm each entry with RET Tap Save program in the program management The edited program is saved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 281: Turning - Programming

    Turning – Programming...

  • Page 282: Overview

    The user interface for programming is displayed Figure 78: Programming menu View bar Toolbar Program management The status bar and the optional OEM bar are not available in the Programming menu. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 283: Block Types

    Further information: "Defining presets", Page 214 Preset block Parameter Description Preset number ID from the preset table Optional: Selection from preset table HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 284: Machine Functions

    M function Number of the M function Optional: Selection from function table Dwell time Time interval between machining steps HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 285: Creating A Program

    Figure 79: Example of a program in the Programming operating mode View bar Simulation window (optional) Block parameters Toolbar Program blocks Program management HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 286: Programming Support

    The name of the program is displayed on the toolbar Enter a unique name in the Name field Confirm the entry with RET Change the unit of measure with the slide switch, if required HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 287: Adding Blocks

    The selected blocks are deleted from the program Tap Delete on the toolbar again 18.3.5 Saving a program Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 288: Using The Simulation Window

    The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Graphic-Position Display of simulation, position values and blocks Position Display of position values and blocks HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 289: Depiction As Contour View

    The contour view uses the following colors (defaults): Figure 80: Simulation window with contour view Machining pattern (white) Current block or machining position (green) Tool contour, tool position and tool track (orange) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 290: Activating The Simulation Window

    Tap each program block, one after the other The program steps are displayed in the simulation window; you can enlarge the detail view as needed Tap Detail view to enlarge Tap Overview to show the overall view HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 291: Managing Programs

    The name of the program is displayed on the toolbar 18.5.5 Saving the program automatically Tap Save program automatically in the program management All changes to the program will be automatically saved immediately HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 292: Deleting A Program

    The parameters of the selected block are displayed Edit the relevant parameters, depending on the block type Confirm each entry with RET Tap Save program in the program management The edited program is saved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 293: File Management

    File management...

  • Page 294: Overview

    Tap File management in the main menu The user interface for file management is displayed Figure 81: File management menu List of available storage locations List of folders in the selected storage location HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 295: File Types

    Tap Create a new folder Tap the input field in the dialog and enter a name for the new folder Confirm entry with RET Tap OK A new folder is created HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 296 Touch the icon of the file you want to move, and drag it to the right The operating elements are displayed Tap Move to In the dialog, select the folder to which you want to move the file Tap Select The file is moved HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 297 Touch the icon of the folder or file you want to delete, and drag it to the right The operating elements are displayed Tap Delete selection Tap Delete The folder or file is deleted HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 298: Opening And Viewing Files

    Tap View The file contents are displayed Tap Close to close the view In this view, you can print PDF files on the printer configured in the product by tapping Print. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 299: Exporting Files

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 300: Importing Files

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 301: Settings

    Settings...

  • Page 302: Overview

    Settings menu. If, for example, the POSITIP 8000 NC1 software option is not activated on the unit, then the settings parameters that are necessary for this software option are not displayed on the unit.

  • Page 303: Overview Of The Settings Menu

    20.6.21 "Spindle axis S" 20.6.9 "Configuring M functions" 20.6.10 "Special settings" 20.7.1 "Firmware information" 20.7.2 "Back up and restore" 20.7.3 "Firmware update" Service 20.7.4 "Reset" 20.7.5 "OEM area" 20.7.18 "Documentation" 20.7.19 "Software options" HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 304: General

    Tap and drag: Touch the touchscreen and drag the arrow upwards from the lower edge Tap: Touch the touchscreen Tap or axis movement: Touch the touchscreen or move the axis Default setting: Tap and drag HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 305: Display

    The position values can describe the actual values or nominal values of the axes. Settings: Actual value Nominal value Default setting: Actual value Distance-to-go indicator Display of the distance-to-go indicator in MDI mode Settings: ON or OFF Default value: ON HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 306 Configuration of the simulation window for MDI mode and program run. Further information: "Simulation window", Page 307 Radial machining axes Display of the radial machining axes in the Turning application mode Settings: Radius Diameter Default value: Radius HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 307: Simulation Window

    Upward: values increase in the upward direction Downward: values increase in the downward direction Default value: Upward The Undo buttons enable the color definitions of the simulation window to be reset to factory settings. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 308: Input Devices

    Off (only multitouch): Operation only possible with the touchscreen, the mouse is deactivated Default setting: Auto (until first multitouch) USB keyboard layout If a USB keyboard is connected: Language selection of the keyboard assignment HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 309: Sounds

    Adds a USB printer or Network printer Further information: "Add printer", Page 310 Remove printer Removes a USB printer or Network printer connected to the product Further information: "Remove printer", Page 311 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 310: Properties

    ("#") or spaces. Description General printer description (optional, arbitrary) Location General location description (optional, arbitrary) Connection Type of printer connection Select the driver Selection of the appropriate driver for the printer HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 311: 20.2.10 Remove Printer

    Default setting: Current system time Date format Format in which the date is displayed Settings: MM-DD-YYYY: month, day, year DD-MM-YYYY: day, month, year YYYY-MM-DD: year, month, day Default setting: YYYY-MM-DD (e.g. "2016-01-31") HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 312: 20.2.12 Units

    Round to 0 and 5: Decimal places ≤ 24 or ≥ 75 are rounded to 0, decimal places ≥ 25 or ≤ 74 are rounded to 5 Default setting: Commercial HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 313: 20.2.13 Copyrights

    Meaning and function Operating Instructions Display of the operating instructions stored on the product Default: no document; the document in the desired language can be added Further information: "Documentation", Page 356 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 314: Sensors

    Length offset of the edge finder Setting range: ≥ 0.0001 Default value: 0.0000 Diameter Diameter of the edge finder Setting range: ≥ 0.0001 Default value for selection of KT 130: 6.0000 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 315: Interfaces

    IPv6 standard gateway Network address of the router connecting a network Preferred DNS server Primary server for mapping the IP address Alternative DNS server Optional server for mapping the IP address HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 316: Network Drive

    Kerberos V5 authentication and packet signing NTLM password hashing NTLM password hashing with signing NTLMv2 password hashing NTLMv2 password hashing with signing Default value: None Configuration of the Mount options Settings: Default value: nounix,noserverino HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 317: Usb

    Parameter Explanation Name Name of the switching function Switching function Selecting whether the switching function should be activated or deactivated Settings: ON or OFF Default setting: ON HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 318 (only with Interval type of switching) Upper limit Selecting the upper limit of the axis position at which switching is to occur (only Interval type of switching) Remove the entry Removing the position-dependent switching function HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 319: User

    Language of the user – Auto login On restart of the product: Automatic login of the last logged-in user Default value: OFF – Remove user account Removal of the user account HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 320: Setup

    Language of the user – Auto login On restart of the product: Automatic login of the last logged-in user Default value: OFF – Remove user account Removal of the user account HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 321: Operator

    Settings ► User ► + Path: Parameter Explanation Adds a new user of the type Operator Further information: "Entering and configuring users", Page 150 It is not possible to add further OEM and Setup-type users. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 322: Axes

    With absolute encoders, an absolute position value is transmitted to the digital readout immediately upon switch-on. In this way the assignment of the actual position to the machine slide position is re-established directly after switch-on. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 323 Relative coordinates are referenced to any other known position (reference point) you define within the coordinate system. Relative coordinate values are also referred to as incremental coordinate values. Figure 83: Rectangular reference system (Cartesian coordinate system) HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 324 Z, respectively. The rotary axes are designated as A, B and C. Principal axis Rotary axis Secondary axis Figure 85: Assignment of the rotary axes and secondary axes to the principal axes HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 325 Z: horizontal principal axis (saddle) Zo: secondary axis on manually operated lathes (top slide), parallel to Z and can be coupled to Z X: principal axis, perpendicular to Z C: rotary axis about Z HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 326: Reference Marks

    Start starts the reference mark search and opens the workspace Reference mark search status Indicates whether the reference mark search was successful Display: Successful Unsuccessful Stop of reference mark search Indicates whether the reference mark search was canceled Display: HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 327: Information

    Further information: "Inputs (Switching functions)", Page 328 Outputs Assignment of the digital output for the respective switching function according to the pin layout Further information: "Outputs (Switching functions)", Page 329 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 328: Inputs (Switching Functions)

    Default value: Not connected If no digital input is assigned to the parameter Automatic feed, the NC START key operating element will be shown during the execution of an MDI block or a program. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 329: Outputs (Switching Functions)

    Definition of the maximum output voltage Setting range: 0 mV ... 5000 mV Default value: 5000 Lower dead band Definition of the lower dead band Setting range: 0 % ... 100 % Default value: 0.000 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 330: Adding M Functions

    Setting range: 100 mm/min ... 10000 mm/min Default value: 2000 The Maximum machine speed cannot be exceeded, even if a higher feed rate has been defined for individual axes. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 331: 20.6.11 Axes X, Y

    Configuration of the Software limit switches Further information: "Software limit switches", Page 341 Start-up time Definition of the required Start-up time until Fmax is reached Setting range: 50 ms ... 10000 ms Default value: 500 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 332 Default value: 100 Positioning window Input of the scaling factor for the positioning aid in MDI mode (only for manually operated linear axes) Setting range: 0.020 mm ... 2.000 mm Default value: 0.100 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 333: 20.6.12 Encoder

    Setting range: 0.1 mm ... 1000 mm Default value: 1.0 Reference point displacement Configuration of the offset between the reference mark and the zero point Further information: "Reference point displacement", Page 337 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 334 For display of a rotary axis as a linear axis: traverse path in mm per revolution Setting range: 0.1 mm ... 1000 mm Default value: 1.0 Reference marks Configuration of the Reference marks Further information: "Reference marks (Encoder)", Page 336 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 335 Positive: The direction of traverse corresponds to the counting direction of the encoder Negative: The direction of traverse does not correspond to the counting direction of the encoder Default value: Positive HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 336: Reference Marks (Encoder)

    OFF: Reference pulses are not evaluated in inverted form Default value: OFF Reference point displacement Configuration of the offset between the reference mark and the zero point Further information: "Reference point displacement", Page 337 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 337: 20.6.14 Reference Point Displacement

    If Compensation is active, the Nominal length and Actual length cannot be edited or generated. Nominal length Input field for Nominal length in mm Actual length Input field for Actual length in mm HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 338: Segmented Linear Error Compensation (Slec)

    The start point defines the position starting from which the compensation is applied to the axis Default value: 0.00000 Create Creates a new table of supporting points based on the entries HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 339: 20.6.18 Outputs

    Fmax Setting range: 1000 mV ... 10000 mV Default value: 9000 Drive enable Assignment of the digital output for the drive enable according to pin layout Default value: Not connected HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 340: 20.6.19 Inputs

    Assignment of the digital input for the enable signal of the servo amplifier according to pin layout Default value: Not connected Signal is low-active If the function is active, the axis is enabled when the signal is low at the input HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 341: 20.6.20 Software Limit Switches

    Configuration of the Inputs for the spindle Further information: "Inputs (S)", Page 344 Gear stages Configuration of the Gear stages for the Gear spindle Further information: "Configuring Gear stages", Page 345 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 342 Setting range: 0 rpm ... 500 rpm Default value: 30 Maximum spindle speed for Definition of the maximum spindle speed for thread cutting thread cutting Setting range: 100 rpm ... 2000 rpm Default value: 1000 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 343: Outputs (S)

    Assignment of the digital output for the clockwise spindle enable according to pin layout Default value: Not connected Enable spindle CCW Assignment of the digital output for the counterclockwise spindle enable according to pin layout Default value: Not connected HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 344: Inputs (S)

    Spindle sleeve final position – Assignment of a digital input for the lower limit switch of the sleeves. The input is used for reversing the spindle with thread cutting. Default value: Not connected HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 345: 20.6.24 Adding Gear Stages

    Setting range: 0 rpm ... 2000 rpm Default value: 1500 Minimum spindle speed Definition of the minimum spindle speed Setting range: 0 rpm ... 500 rpm Default value: 50 Remove Removal of the selected gear stage HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 346: Service

    Version number of the encoder parameters ncParam.xml Version number of the NC parameters spindle.xml Version number of the spindle axis parameters io.xml Version number of the parameters for inputs and outputs HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 347: Back Up And Restore

    Restoring of user files of the product Further information: "Restore user files", Page 365 Back up user files Backing up of user files of the product Further information: "Back up user files", Page 143 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 348: Firmware Update

    Reset to shipping conditions Resetting of the settings to the factory default setting and deletion of the user files from the unit’s memory area Further information: "Reset to shipping conditions", Page 366 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 349: Oem Area

    OFF: The OEM bar is not displayed Default value: OFF Bar items Configuration of the Bar items on the OEM bar Further information: "Adding OEM-Bar items", Page 350 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 350: Adding Oem-Bar Items

    Special functions: Further information: "Special functions OEM bar item", Page 353 Document: Further information: "Document OEM bar item", Page 353 Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 351: Logo Oem Bar Item

    Spindle speed Setting the spindle speed Setting range: depends on the configuration of the spindle axis S Default value: 0 Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 352: 20.7.10 M Function Oem Bar Item

    Copies a selected image file to the storage location /Oem/ Images File format: PNG, JPG, PPM, BMP , or SVG Image size: Max. 100 x 70 px Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 353: 20.7.11 Special Functions Oem Bar Item

    Selecting the desired image for depicting the function Upload image file Copies a selected image file to the storage location /Oem/ Images Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 354: Settings (Oem Area)

    Settings: ON or OFF Default value: OFF M functions For the configuration, see "Configuring M functions", Page 356 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 355: 20.7.15 Text Database

    Default value: Standard Input Assignment of the digital input in accordance with pin layout in order to show the message Default value: Not connected Remove the entry Removing the message entry HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 356: 20.7.17 Configuring M Functions

    USB mass storage device to the product. The latest version can be downloaded from the download area at www.heidenhain.de. Parameters Explanation Add Operating Instructions Adding the Operating Instructions in the desired language HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 357: 20.7.19 Software Options

    "Back up OEM specific folders and files", Page 139 Restore OEM specific folders and Restoring the settings of the OEM area as a ZIP file files Further information: " Restore OEM specific folders and files", Page 139 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 359: Service And Maintenance

    Service and maintenance...

  • Page 360: Overview

    To deactivate the cleaning mode, tap anywhere on the touchscreen An arrow appears at the bottom of the screen Drag the arrow up The screen is switched on and shows the user interface last displayed HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 361: Maintenance Plan

    When connecting the peripheral devices (e.g. encoders), the operating company must ensure safe resumption of operation and assign authorized and appropriately qualified personnel to the task. Further information: "Obligations of the operating company", Page 32 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 362: Updating The Firmware

    Starting a firmware update Tap Settings in the main menu Tap Service Open in the sequence Firmware update Continue The service application is launched HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 363 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 364: Restore Settings

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 365: Restore User Files

    Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 366: Reset All Settings

    Tap OK to confirm shutdown of the product The product is shut down All settings are reset and the user files are deleted To restart the product, switch it off and then back on HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 367: What To Do If

    What to do if ...

  • Page 368: Overview

    22.2.1 Restoring the firmware On a computer, create the folder "heidenhain" on a USB mass storage device (FAT32 format). In the "heidenhain" folder, create the folder "update" Copy the new firmware to the "update" folder Rename the firmware "recovery.dro"...

  • Page 369: Restore Settings

    22.3 Malfunctions If faults or malfunctions that are not listed in the "Troubleshooting" table below occur during operation, refer to the machine tool builder's documentation or contact a HEIDENHAIN service agency. HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 370: Troubleshooting

    Incorrect feed rate Check the axis settings Qualified not limit the axis speed override settings personnel Rapid traverse key does Incorrect rapid Check settings Qualified not work traverse settings Page 328 personnel HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 371 Use another USB port The type or format- Use another USB mass Qualified ting of the USB mass storage device personnel storage device is not Format USB mass storage supported device with FAT32 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 372 User login is not possible Password does not As user with higher Qualified exist permission level, reset the personnel password Page 150 To reset the OEM password, contact the HEIDENHAIN service agency HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 373: Removal And Disposal

    Removal and disposal...

  • Page 374: Overview

    Forward the product and the backup battery to recycling in accordance with the applicable local disposal regulations If you have any questions about the disposal of the product, please contact a HEIDENHAIN service agency HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 375: Specifications

    Specifications...

  • Page 376: Overview

    Interpolation at 1 V 4096-fold Touch probe connection Voltage supply DC 5 V or DC 12 V 5 V or floating switching output Max. cable length with HEIDENHAIN cable 30 m HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 377 Front panel and side panels: IP 65 Rear panel: IP 40 Mass 3.5 kg With Single-Pos stand: 3.6 kg With Duo-Pos stand: 3.8 kg With Multi-Pos stand: 4.5 kg With Multi-Pos holder: 4.1 kg HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 378: Product Dimensions And Mating Dimensions

    Product dimensions and mating dimensions All dimensions in the drawings are in millimeters. 35.5 30.5 Figure 87: Dimensions of housing X112 X116 X100 Figure 88: Dimensions of rear panel of the product HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 379: Product Dimensions With Single-Pos Stand

    Figure 89: Product dimensions with Single-Pos stand 24.3.2 Product dimensions with Duo-Pos stand ISO 7092-4 ISO 7092-4 ISO 7380-M4x8 Md = 2.6 Nm ISO 7380-M4x8 Md = 2.6 Nm 115.5 Figure 90: Product dimensions with Duo-Pos stand HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 380: Product Dimensions With Multi-Pos Stand

    Md = 15 Nm max. 1 18.75 12.3 Figure 91: Product dimensions with Multi-Pos stand 24.3.4 Product dimensions with Multi-Pos holder Md = 15 Nm max. 1 Figure 92: Product dimensions with Multi-Pos holder HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 381: Index

    MDI mode of operation copying........ 296 Electrical specialist..... 31 example....... 185, 188 creating........ 295 Encoders Menu deleting........ 297 configuring axis parameters. 116 File management....85 moving......... 296 manual operation... 76, 212, 222 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 382 Status bar........93 slide switch......68 adjusting the quick access status bar....... 93 deleting......280, 292 menu........94 toggle switch......68 deleting blocks..... 275, 287 calculator........ 96 opening..258, 267, 279, 291 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 383 82 program run menu....81 Settings menu....... 87 Switch-off menu..... 88 user login menu..... 86 User login......70, 86 Users deleting........ 152 Wiring switching inputs and outputs........54 Wizard........102 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...

  • Page 384: List Of Figures

    Example workpiece – programming a bolt hole pattern and a row of holes......192 Image 42: Image 43: Example workpiece – simulation window................195 Example workpiece – drilling a bolt hole pattern and a row of holes........196 Image 44: HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 385 Image 87: Dimensions of housing......................378 Image 88: Dimensions of rear panel of the product................378 Image 89: Product dimensions with Single-Pos stand................379 Image 90: Product dimensions with Duo-Pos stand................379 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 386 List of figures Image 91: Product dimensions with Multi-Pos stand................380 Image 92: Product dimensions with Multi-Pos holder................380 HEIDENHAIN | POSITIP 8000 | Operating Instructions | 09/2018...
  • Page 387 DR. JOHANNES HEIDENHAIN GmbH Dr.-Johannes-Heidenhain-Straße 5 83301 Traunreut, Germany  +49 8669 31-0  +49 8669 32-5061 E-mail: info@heidenhain.de Technical support  +49 8669 32-1000 Measuring systems  +49 8669 31-3104 E-mail: service.ms-support@heidenhain.de NC support  +49 8669 31-3101 E-mail: service.nc-support@heidenhain.de NC programming ...

Table of Contents