Dtmf Parameters - AudioCodes Mediant 800B MSBR User Manual

Mediant 800B MSBR

67.9.3 DTMF Parameters

The dual-tone multi-frequency (DTMF) parameters are described in the table below.
Parameter
Web/EMS: DTMF Transport
Type
CLI: DTMF-transport-type
[DTMFTransportType]
Web: DTMF Volume (-31 to 0
dB)
EMS: DTMF Volume (dBm)
CLI: DTMF-volume
[DTMFVolume]
Web: DTMF Generation Twist
EMS: DTMF Twist Control
CLI: DTMF-generation-twist
[DTMFGenerationTwist]
EMS: DTMF Inter Interval
(msec)
CLI: inter-digit-interval
[DTMFInterDigitInterval]
EMS: DTMF Length (msec)
[DTMFDigitLength]
EMS: Rx DTMF Relay Hang
Over Time (msec)
CLI: default-dtmf-signal-
duration
[RxDTMFHangOverTime]
EMS: Tx DTMF Relay Hang
Over Time (msec)
CLI: digit-hangover-time-tx
[TxDTMFHangOverTime]
Web/EMS: NTE Max Duration
CLI: telephony-events-max-
duration
Version 6.8
Table 67-39: DTMF Parameters
Determines the DTMF transport type.

[0] Mute DTMF = DTMF digits are removed from the voice
stream and are not relayed to remote side.

[2] Transparent DTMF = DTMF digits remain in the voice
stream.

[3] RFC 2833 Relay DTMF = (Default) DTMF digits are removed
from the voice stream and are relayed to remote side according
to RFC 2833.

[7] RFC 2833 Relay Decoder Mute = DTMF digits are sent
according to RFC 2833 and muted when received.
Note: This parameter is automatically updated if the parameters
TxDTMFOption or RxDTMFOption are configured.
Defines the DTMF gain control value (in decibels) to the Tel side.
The valid range is -31 to 0 dB. The default is -11 dB.
Note: This parameter can also be configured in a Tel Profile.
Defines the range (in decibels) between the high and low frequency
components in the DTMF signal. Positive decibel values cause the
higher frequency component to be stronger than the lower one.
Negative values cause the opposite effect. For any parameter
value, both components change so that their average is constant.
The valid range is -10 to 10 dB. The default is 0 dB.
Note: For this parameter to take effect, a device reset is required.
Defines the time (in msec) between generated DTMF digits to the
Tel side (if TxDTMFOption = 1, 2 or 3).
The valid range is 0 to 32767. The default is 100.
Defines the time (in msec) for generating DTMF tones to the Tel
side (if TxDTMFOption = 1, 2 or 3). It also configures the duration
that is sent in INFO (Cisco) messages.
The valid range is 0 to 32767. The default is 100.
Defines the Voice Silence time (in msec) after playing DTMF or MF
digits to the Tel side that arrive as Relay from the IP side.
Valid range is 0 to 2,000 msec. The default is 1,000 msec.
Defines the Voice Silence time (in msec) after detecting the end of
DTMF or MF digits at the Tel side when the DTMF Transport Type
is either Relay or Mute.
Valid range is 0 to 2,000 msec. The default is 1,000 msec.
Defines the maximum time for sending Named Telephony Events /
NTEs (RFC 4733/2833 DTMF relay) to the IP side, regardless of
855
67. Configuration Parameters Reference
Description
Mediant 800B MSBR