AudioCodes Mediant 800B MSBR User Manual page 900

Parameter
Web: MLPP DiffServ
EMS: Diff Serv
CLI: mlpp-diffserv
[MLPPDiffserv]
Web/EMS: Preemption Tone
Duration
CLI: preemp-tone-dur
[PreemptionToneDuration]
Web: MLPP Normalized Service
Domain
EMS: Normalized Service Domain
CLI: mlpp-norm-ser-dmn
[MLPPNormalizedServiceDomain]
CLI: mlpp-nwrk-id
[MLPPNetworkIdentifier]
Web: MLPP Default Service
Domain
EMS: Default Service Domain
CLI: mlpp-dflt-srv-domain
[MLPPDefaultServiceDomain]
User's Manual
Precedence Level value, the default value is used in the
Resource-Priority header of the outgoing SIP INVITE request. In
this scenario, the character string is sent without translation to a
numerical value.
Defines the DiffServ value (differentiated services code
point/DSCP) used in IP packets containing SIP messages that
are related to MLPP calls. This parameter defines DiffServ for
incoming and outgoing MLPP calls with the Resource-Priority
header.
The valid range is 0 to 63. The default is 50.
Defines the duration (in seconds) in which the device plays a
preemption tone to the Tel and IP sides if a call is preempted.
The valid range is 0 to 60. The default is 3.
Note: If set to 0, no preemption tone is played.
Defines the MLPP normalized service domain string. If the
device receives an MLPP ISDN incoming call, it uses the
parameter (if different from 'FFFFFF') as a Service domain in
the SIP Resource-Priority header in outgoing INVITE messages.
If the parameter is configured to 'FFFFFF', the Resource-Priority
header is set to the MLPP Service Domain obtained from the
Precedence IE.
The valid value is 6 hexadecimal digits. The default is '000000'.
Note: This parameter is applicable only to the MLPP NI-2 ISDN
variant with CallPriorityMode set to 1.
Defines the MLPP network identifier (i.e., International prefix or
Telephone Country Code/TCC) for IP-to-ISDN calls, according
to the UCR 2008 and ITU Q.955 specifications.
The valid range is 1 to 999. The default is 1 (i.e., USA).
The MLPP network identifier is sent in the Facility IE of the ISDN
Setup message. For example:

MLPPNetworkIdentifier set to default (i.e., USA, 1):
PlaceCall- MLPPNetworkID:0100
MlppServiceDomain:123abc, MlppPrecLevel:5
Fac(1c): 91 a1 15 02 01 05 02 01 19 30 0d 0a 01 05 0a 01 01
04 05 01 00 12 3a bc

MLPPNetworkIdentifier set to 490:
PlaceCall- MLPPNetworkID:9004
MlppServiceDomain:123abc, MlppPrecLevel:5
Fac(1c): 91 a1 15 02 01 0a 02 01 19 30 0d 0a 01 05 0a 01 01
04 05 90 04 12 3a bc
Defines the MLPP default service domain string. If the device
receives a non-MLPP ISDN incoming call (without a Precedence
IE), it uses the parameter (if different than "FFFFFF") as a
Service domain in the SIP Resource-Priority header in outgoing
(Tel-to-IP calls) INVITE messages. This parameter is used in
conjunction with the parameter SIPDefaultCallPriority.
If MLPPDefaultServiceDomain is set to 'FFFFFF', the device
interworks the non-MLPP ISDN call to non-MLPP SIP call, and
the outgoing INVITE does not contain the Resource-Priority
header.
The valid value is a 6 hexadecimal digits. The default is
900
Mediant 800B MSBR
Description
Document #: LTRT-12813