Acura 2002 RSX Service Manual page 754

Shafts and Clutches
Secondary Shaft 2nd Gear Clearance tnspection (cont,d)
3 .
4 .
recheck.
THRUSl
lf the clearance is out of standard, remove tne
37 x 58 mm thrust washer and measure its
t h i c k n e s s .
Select and install a new thrust washer, then
UST WASHER, 37 x 58 mm
No.
Part Number
Thickness
,l
9 0 5 1 1 . P R P - 0 1 0
3 . 9 0 0 m m ( 0 . 1 5 4 i n . )
2
9 0 5 1 2 - P R P - 0 ' 1 0 3 . 9 2 5 m m ( 0 . 1 5 5 i n . )
3
9 0 5 1 3 - P R P - 0 1 0 3 . 9 5 0 m m ( 0 . 1 5 6 i n . )
4 9 0 5 1 4 - P R P - 0 1 0 3 . 9 7 5 m m ( 0 . 1 5 6 i n . )
5
9 0 5 1 5 - P R P . C
1 0 4 . 0 0 0 m m { 0 . 1 5 7 i n . )
6 9 0 5 1 6 - P R P - 0 1 0 4 . 0 2 5 m m ( 0 . 1 5 8 i n . )
7
9 0 5 1 7 - P R P - 0 ' 1 0
4 . 0 5 0 m m ( 0 . 1 5 9 n . )
8
9 0 5 1 8 - P R P - 0 ' 1 0 4 . 0 7 5 m m ( 0 . 1 6 0 n .
9 9 0 5 1 9 - P R P - 0 1 0 4 . 1 0 0 m m ( 0 . 1 6 1 n . )
1 0 90520-PRP-010 4 . 1 2 5 m m ( 0 . 1 6 2 n . )
1 1
9 0 s 2 1 - P R P - 0 1 0
4 . 1 5 0 m m { 0 . 1 6 3 i n
1 2
9 0 5 2 2 - P R P - 0 1 0
4 . ' 1 7 5 m m ( 0 . ' 1 6 4 n . )
I J
90523-PRP-000 4 . 2 0 0 m m ( 0 . 1 6 5 n . )
1 4
90524-PRP-000 4 . 2 2 5 m m ( 0 . 1 6 6 n .
t c
90525-PRP-000 4 . 2 5 0 m m { 0 , ' 1 6 7
n .
l 6
90526-PRP-000 4 . 2 7 5 m m ( 0 . 1 6 8 n .
1 7
1 8
l9szll&p:olQ
90528-PRP-000
4iqqt11!! 10:10q!n.)
4 . 3 2 5 m m ( 0 . 1 7 0 i n . )
1 9 90529-PRP-000 4 . 3 5 0 m m ( 0 . 1 7 1 i n . )
20 90530-PRP-000
4 . 3 7 5 m m ( 0 . 1 7 2 i n . )
5 .
6 .
After replacing the thrust washer, make sure the
clearance is within standard.
Disassemble the shaft and gears.
14-222