Subaru Legacy 2005 Service Manual page 2190

AUTOMATIC TRANSMISSION (DIAGNOSTICS)
3. CLEAR MEMORY MODE
1) On the «Main Menu» display screen, select the
{Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display
screen, select the {Transmission} and press the
[YES] key.
3) Press the [YES] key after the information of
transmission type is displayed.
4) On the «Transmission Diagnosis» display
screen, select the {Clear Memory} and press the
[YES] key.
NOTE:
When {Clear Memory 2} is selected and executed,
DTC and learned control memory is cleared. If
Clear Memory 2 is performed, execute the advance
operation of learning control. <Ref. to 4AT(diag)-
18, FACILITATION OF LEARNING CONTROL,
OPERATION, Subaru Select Monitor.>
4. FACILITATION OF LEARNING CON-
TROL
1) Shift the select lever to "P" range, and apply
parking brake.
2) Lift-up the vehicle.
3) Connect the Subaru Select Monitor to data link
connector, and then turn the ignition switch to ON.
4) Perform the {Clear Memory 2} using Subaru Se-
lect Monitor. <Ref. to 4AT(diag)-18, CLEAR MEM-
ORY MODE, OPERATION,
Monitor.>
5) Using Subaru Select Monitor, check that the
DTC is not output. <Ref. to 4AT(diag)-16, READ
DIAGNOSTIC TROUBLE CODE (DTC), OPERA-
TION, Subaru Select Monitor.>
6) Warm-up the engine until the ATF temperature
which is displayed on the Subaru Select Monitor is
within 60 — 90°C (140 — 194°F). <Ref. to 4AT(di-
ag)-16, READ CURRENT DATA, OPERATION,
Subaru Select Monitor.>
7) Shift the select lever to "R" range.
8) Turn all switches including headlight, air condi-
tioner, seat heater, rear defogger and etc. to OFF.
9) With turning ignition key to OFF, wait for 30 sec-
onds until ACC goes OFF.
10) Depress the brake pedal fully until the facilita-
tion of learning control is completed when the
"Communication Failed!" is displayed on Subaru
Select Monitor.
11) Turn the ignition switch to ON.
12) Check that the Subaru Select Monitor is re-
turned to normal operation.
13) Shift the select lever to "P" range, and then wait
for more than 3 seconds.
14) Shift the select lever to "R" range, and then wait
for more than 3 seconds.
Subaru Select Monitor
15) Shift the select lever to "N" range, and then wait
for more than 3 seconds.
16) Shift the select lever to "D" range, and then wait
for more than 3 seconds.
17) Shift the select lever to "N" range, and then wait
for more than 3 seconds.
18) Slowly depress the accelerator pedal fully.
19) Slowly release the accelerator pedal fully.
20) Start the engine, and idle it.
21) Shift the select lever to "D" range.
22) Start the facilitation of learning control. At this
time, the SPORT indicator light in the combination
meter start blinking at 2 Hz. When the SPORT indi-
cator light does not blink, turn the ignition switch to
OFF and repeat the procedures from step 4). When
the SPORT indicator light stop blinking at 2 Hz and
goes OFF, facilitation of learning control is complet-
ed.
NOTE:
When blinking of SPORT indicator light changes
from 2 Hz to 4 Hz during facilitation of learning con-
trol, repeat the procedure from step 4).
23) Shift the select lever to "N" range, and then turn
the ignition switch to OFF.
24) Shift the select lever to "P" range to complete
the facilitation of learning control.
Subaru Select
4AT(diag)-18