Fujitsu F2MC-16LX Hardware Manual page 592

INDEX
expanded I/O serial interface, interrupt function of
................................................................... 392
expanded I/O serial interface, overview of ........... 378
expanded I/O serial interface, overview of operation
of ................................................................386
expanded I/O serial interface, register of ............. 379
extended intelligent I/O service (EI
extended intelligent I/O service (EI
each transfer), processing time for.............. 90
extended intelligent I/O service (EI
register (ISCS) ............................................. 86
extended intelligent I/O service (EI
processing procedure of .............................. 88
extended intelligent I/O service (EI
processing specification of sample
program for .................................................. 97
extended intelligent I/O service (EI
setting procedure of ..................................... 89
external address output control register (HACR)
................................................................... 168
external bus 16-bit data bus mode, pin state in
........................................................... 149, 151
external bus 8-bit data bus mode .........................150
external bus 8-bit data bus mode, pin state in ..... 152
external connection of peripheral device,
conditions for.............................................. 353
external interrupt request level ............................. 354
external interrupt request register ........................ 350
external interrupt unit, operation of ...................... 351
external level register ........................................... 350
external memory access control signal ................ 172
external memory access, I/O signal pin for .......... 164
external pin in each mode, operation of ............... 163
external shift clock mode......................................387
external trigger ..................................................... 376
external-reset pin, block diagram of ..................... 106
F
2
F MC-16LX instruction list.................................... 537
flag change suppress prefix ................................... 39
flash memory control status register (FMCS)....... 470
flash memory to the read/reset state, setting ....... 484
flash memory write/erase ..................................... 483
flash memory, operation for writing to .................. 486
flash memory, resuming sector erasure of ........... 491
flash memory, suspending sector erasure for ......490
flash memory, writing data to ............................... 485
flash microcomputer programmer (using power from
user system), example of minimum connection
................................................................... 501
576
2
OS)................. 81
2
OS) (time for
2
OS) status
2
OS),
2
OS),
2
OS),
flash microcomputer programmer, system
configuration of .......................................... 497
free-running timer (match with compare register 0),
clear timing of ............................................ 245
free-running timer, count timing of ....................... 245
fujitsu standard serial onboard writing, pin use for
................................................................... 495
function selection ................................................. 418
G
general-purpose register........................................ 28
general-purpose register (register bank)................ 37
H
handling device, note on ........................................ 19
hardware component, initial value ....................... 346
hardware interrupt function .................................... 55
hardware interrupt operation.................................. 59
hardware interrupt operation flow .......................... 60
hardware interrupt processing time........................ 65
hardware interrupt, configuration of ....................... 56
hardware interrupt, procedure for using................. 61
hardware interrupt, return from .............................. 58
hardware interrupt, starting .................................... 58
hardware interrupt, suppressing ............................ 56
hardware sequence flag....................................... 476
hold function, operation of.................................... 178
I
I/O circuit type ........................................................ 16
I/O map ................................................................ 506
I/O port, function of .............................................. 182
I/O port, register for.............................................. 183
I/O register address pointer (IOA).......................... 75
I/O register address pointer register (I/OA)............ 85
2
I C interface function ........................................... 424
2
I C interface register, list of.................................. 426
2
I C interface, block diagram of............................. 425
indirect addressing............................................... 524
input capture ........................................................ 236
input capture data register (IPCP0, 1) ................. 237
input capture register, list of................................. 237
input capture timing, example of .......................... 244
input capture, block diagram of............................ 236
input pin, selection of ........................................... 296
input resistor register (RDR0, ROR1) .................. 187
input/output timing................................................ 390
instruction map, structure of................................. 551