Installation Procedure In The Imageware Accounting Manager (Hereinafter Referred To Iwam) Environment; Installing The Original Holder; Checking Components; Installation Procedure - Canon iR3245 Series Service Manual

12) Insert the power plug into the outlet.
13) Turn ON the main power switch.
14) Get in Service Mode (COPIER > FUNCTION > INSTALL > CARD)
and enter the card number to use (1 to 2000).
- Enter the smallest card number of the cards used by the user.
- From the entered number, up to 1000 cards can be used.
15) Follow the instructions on the shutdown sequence screen to turn OFF and
then ON the main power switch.
16) Insert the card with registered valid number to check it's at standby state.
2.6.5 Installation Procedure in the imageWARE
Accounting Manager (hereinafter referred to iWAM)
Environment
iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
1) Check to see that 'ID00000001 to ID00001000' have been created in '[Ad-
ditional Functions] > [System Settings] > [Dept. ID Management] >
[Register Dept.ID/Password] / [Page Totals]' (In the case of entering '1' as
the first number in 'Service Mode > COPIER > FUNCTION > INSTALL
> CARD')
2) Press [Reset] to exit from [Additional Functions].
3) Select [Additional Functions] > [System Settings] > [Network Settings]
> [TCP/IP Settings] > [IP Address Settings], and then make the setting of
[IP Address], [Gateway Address], [Subnet Mask] according to the user
environment.
4) Press [Reset] to exit from [Additional Functions].
5) Turn OFF the power supply following the shutdown sequence.
6) Turn on the main power switch.
7) [Additional Functions] > [System Settings] > [System Manager Settings],
and then input any number into [System Manager ID] and [System Pass-
word].
[Additional Functions] > [System Settings] > [System Manager Settings] is
selected and [System Manager ID] and [System Password] are registered,
'Registration of card to the device' is impossible to execute in the setting of
iWAM.
8) Press [Reset] to exit from [Additional Functions].

2.7 Installing the Original Holder

2.7.1 Notice At Installation
iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
See "Combination Table of Accessories" when installing this equipment.

2.7.2 Checking Components

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
<Document Tray-J1>
[1]
[2] [3]
F-2-82
[2] 1
[1] Document tray
[2]*1 Washer
[3]*1 Stepped screw (RS tightening; M4X18)
[4]*1 Stepped screw (M4X17.6)
[5]*2 Stepped screw (M4X10.8)
*1 Not used with this machine.
*2 Only the head of a screw is painted in white.
0019-9964

2.7.3 Installation Procedure

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
A: If the card reader is not equipped to the host machine
1) Remove the 2 face cover seals [1]. (Do not use the removed face cover
seals.)
2) Install the 2 stepped screw (M4X10.8) [1] with the reader right cover.
0019-8446
0018-8091
[1]
1
[3] 1 [4] [5]
F-2-83
F-2-84
Chapter 2
2
1pc.
2pc.
2pc.
2pc.
2pc.
0018-8203
[1]
2-21