BRP Evinrude E-TEC G2 Service Manual page 455

Installer Handle, P/N 345822
Installer, P/N 358521 378
Installer, P/N 359079 410
Large Puller Jaws, P/N 432129
388
MPI-2 Adapter, P/N 767994
Oetiker Pincers, P/N 787145
Pinion Bearing Remover and Installer, P/N
5005927 380, 381
Pinion Nut Holder, P/N 334455
Pinion Nut Starting Tool, P/N 342216
Piston Stop Tool, P/N 342679
Press Fixture Nose, P/N 358161
412
Primary Lock Tool, P/N 777077
Propeller Shaft Bearing Housing Installer, P/N
395, 412
354057
Propeller Shaft Bearing Housing Puller Kit, P/N
354060 375, 378, 398
Puller Adapter, P/N 358520
Puller Bridge, P/N 432127
Puller Stud, P/N 358294
Puller Tool, P/N 358520
Puller Tube Assembly, P/N 354175
Puller Wrench, P/N 334359
Puller, P/N 354177 375, 398
Rod Cap Alignment Fixture, P/N 396749
Seal Installation Tool, P/N 330268
Seal Installation Tool, P/N 354056
Secondary Lock Installer, P/N 777079
Secondary Lock Tool, P/N 777078
Shift Rod Bushing Installer, P/N 358997
Shift Rod Installer Tool, P/N 358162
378, 393, 411
Shim Gauge Bar, P/N 358164
Slide Hammer, P/N 391008
Slide Hammer, P/N 432128
Small Puller Jaws, P/N 432131
Spanner Nut Wrench, P/N 358165
398, 413
Spanner Socket, P/N 359224
Spanner Socket, P/N 359225
Spanner Wrench, P/N 359080
Spanner Wrench, P/N 432400
Spanner Wrench, P/N 912084
350
Stator Test Adaptor, P/N 5006211
Steering Lock Tool, P/N 357717
202
Syringe, P/N 346936
90
Tee, P/N 764151
395, 412
377, 379, 386,
90
18
376, 395
394
136
393, 395, 411,
141
400
386, 387, 388
375, 378, 398
379
375, 398
379
260
386
390
141
140
385
368, 376,
391, 409
254
377
387
374, 396,
345, 348
340, 342
330, 332
405, 408
330, 332, 348,
125
49, 50, 51, 52
Temperature Gun, P/N 772018
Terminal Release Tool, P/N 351413
Test Probe Kit, P/N 342677
Thermal Joint Compound, P/N 322170
Timing Lead, P/N 587316
Torquing Socket, P/N 346187
Wrench Retainer, P/N 341438
Wrist Pin and Retaining Ring Driver, P/N
396747 257
Wrist Pin Cone, P/N 331913
Wrist Pin Pressing Tool, P/N 396747
Torque Charts
Standard Torque Specifications
Trim and Tilt
Circuits 132
Electric Motor Service
Electrical Circuit Tests
Filling 332
Fluid Level 332
Fluid Type 38
Manifold:
328
Assembly
Disassembly
Filters 325
Installation 325
324
Removal
323
Service
43
Tilt Limit Setting
Trim Sender Service
Trim Rod
Cleaning and Inspection
Installation 331
Removal 330
Service 330
Troubleshooting
12 V Charging Circuit
Auxiliary Battery Charge Circuit
Charging System Tests
Cylinder Drop Tests
Diagnostic Procedures
Fuel Control Adjustment
Fuel System 160
122
Ignition
Inductive Amp Meter Test
Oiling System 198
Outboard Excessive Smoking
Outboard Hard to Start
Outboard Starts and Stalls
Outboard Starts, Low Maximum RPM
Index
219
142
304, 369
219
137
246, 261
376, 395
257
247
7
329
133
327
344
331
127
127
126
108
102
108
126
443
441
442
443
I-455
I