Agilent Technologies ESA-E Series Programmer's Manual page 378

Index
reference position, normalized,
5-44
reference selection for calibration,
5-1 2
register
calibration condition, 5-133 ,
5-134
condition, 2- 4
event, 24
event enable, 2 4
frequency condition, 5-135 ,
5-136
integrity condition, 5-137, 5-13 8
negative transition, 24
operation condition, 5-131 ,
5-13 2
positive transition, 2-4
power condition, 5-140, 5-14 1
questionable condition, 5-134 ,
5-135, 5-140, 5-141
service request enable, 2-1 3
status byte, 2-1 1
remote
interface (SCPI) error queue ,
7-1 3
reset, IEEE command, 5-8
resolution bandwidt h
on/off, 5-8 7
setting, 5-8 7
RF alignment on/off, 5-1 1
RF calibration, 5-1 3
RF overload reset, 5-63
RS-232 bus, 1-12
configuration, 1-1 2
RTS for serial bus, 5-14 4
S
sample detection, 5-9 7
save, IEEE command, 5- 8
saving
trace data, 5-152
saving data to files, 5-7 1
saving limit lines, 5-74
saving screens, 5-74
saving states, 5-74
saving traces, 5-7 4
scaling, 5-4 7
SCPI
version of, 5-15 1
SCPI remote interface error
queue
characteristics, 7-13
screen s
storing, 5-74
self-test, 5-9
serial bus, 1-1 2
DTR, 5-143
receive BAUD, 5-144
receive PACE, 5-145
RTS, 5-144
transmit PACE, 5-14 5
serial number, query, 5-6
service request (SRQ) method, 2-7
service request enable register,
2-1 3
service request, IEEE command ,
5- 8
signal peaks, 5-29, 5-30, 5-15 4
signal tracking, 5-3 2
single vs. continuou s
measurement mode, 548,
5-49, 5-51, 5-52, 5-59, 5-60 ,
5-61, 5-65, 5-66, 5-68, 5-69 ,
5-77, 5-78, 5-80, 5-8 1
smoothing trace, 5-155, 5-157
source
internal tracking generator,
5-126
See also tracking generator
source calibration, internal, 5-14
source output on/off, 5-7 6
span
markers, 5-28
span markers, 5-34, 5-3 6
span setting, 5-101, 5-102
speaker, on/off, 5-151
SRE command, 2-6
SRQ, 5- 8
SRQ method, 2- 8
standard event status
enable register, 2-16
standard event status byte
enable and read, 5- 5
standard event status register ,
2-1 4
standard event status register ,
IEEE command, 5- 6
standard operation
condition register, 2-18
event enable register, 2-2 0
status group, 2-17
start frequency, 5-10 2
start measurement, 5-9, 5-60
state
changing, 5-82, 5-83, 5-85, 5-87 ,
5-89, 5-91, 5-95, 5-97, 5-98 ,
5-100, 5-104, 5-110, 5-112 ,
5-11 7
get data, 5-6
recalling, 5- 7
saving, 5-8
states
loading from file, 5-72
storing, 5-74
status
preset, 5-132
status byt e
clearing, 5-5
status byte register, 2-1 1
status byte, IEEE command, 5-9
status command, 2-6, 2-9
status enable register, 2-1 6
status group, 2-1 7
data questionable, 2-2 1
status register commands, 2-6
status registers, 2-3
operation status condition, 2-1 8
operation status event enable,
2-1 9
querying, 2-10
questionable, 2-20, 2-22, 2-23 ,
2-24, 2-26
setting, 2-10
standard event, 2-14
status subsystem, 5-131, 5-133
STB command, 2-6
stop command, 5-10
stop frequency, 5-103
storing
limit lines, 5-74
screens, 5-7 4
states, 5-74
traces, 5-7 4
subtracting traces, 5-157, 5-15 8
sweep time, 5-117, 5-118, 5-119 ,
5-120, 5-121, 5-122, 5-123
synchronization, 5-7, 5-9
synta x
drawings, 1-10
system configuration, 5-14 3
system configuration query, 5-146
system options, 5-148
T
talker, 1-1 0
test limit
maximum, 5-24
test limits, 5-1 7
test, IEEE command, 5- 9
time
setting, 5-15 1
time display, 5-4 1
time since power-on, 5-148, 5-149
timing control, 5-7, 5-9
title display, 54 2
trace
adding, 5-154
blank, 5-15 8
copying files, 5-152
exchange data, 5-153
max hold, 5-158
4
Index