Emerson R&S SGT100A User Manual page 488

®
R&S SGT100A
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:VCC:OFFSet
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:VCC:MIN
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:VCC:MAX
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:VCC:VALue:PEP?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:VCC:VALue:LEVel?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:VCC:VALue?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:PIN:MIN
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:PIN:MAX
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:POWer:OFFSet?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:MODE
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:SCALe
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:GAIN:PRE
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:GAIN:POST
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:FILE:CATalog?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:PV:FILE:CATalog?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:FILE[:SELect]
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:PV:FILE[:SELect]
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:FILE:DATA
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:PV:FILE:DATA
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:FILE:NEW
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:PV:FILE:NEW
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:INTerp
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:COEFficients
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:COEFficients:CATalog?
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:COEFficients:STORe
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:COEFficients:LOAD
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:CLIPping:FROM
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:CLIPping:TO
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:DETRoughing:FUNCtion
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:DETRoughing:COUPling
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:DETRoughing:FACTor
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:SHAPing:DETRoughing:PEXPonent
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:STATe <State>
Enables the output of a control signal that follows the RF envelope.
Parameters:
<State>
Example:
Manual operation:
[:SOURce<hw>]:IQ:OUTPut[:ANALog]:ENVelope:ADAPtion <AdaptionMode>
Defines the envelope voltage adaption mode.
User Manual 1176.8674.02 ─ 12
1 | ON | 0 | OFF
*RST: 0
See Example"Generating an RF envelope signal and defining
the shaping function" on page 485
See "RF Envelope" on page 178
Remote control commands
SOURce subsystem
..........................................492
............................................... 493
.............................................. 493
...................................493
.................................493
.......................................... 494
.................................................494
................................................495
.................................... 495
..................................... 495
.....................................496
............................... 496
............................. 496
......................... 496
.................... 496
........................... 496
......................496
............................... 497
.......................... 497
................................497
...........................497
..................................... 497
............................497
............. 498
................ 498
.................. 498
....................... 499
............................ 499
...............500
........... 499
........... 499
......... 500
488