Table of Contents
Advertisement
Z8018x
Family MPU User Manual
xi
Software Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Figure 74. CPU Register Configurations . . . . . . . . . . . . . . . . . . . . . 176
Figure 75. Register Direct - Bit Field Definitions . . . . . . . . . . . . . 181
Figure 76. Register Indirect Addressing . . . . . . . . . . . . . . . . . . . . . . 181
Figure 77. Indexed Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Figure 78. Extended Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Figure 79. Immediate Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Figure 80. Relative Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Figure 81. AC Timing Diagram 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Figure 82. AC Timing Diagram 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Figure 83. CPU Timing (IOC = 0) (I/O Read Cycle,
I/O Write Cycle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Figure 84. DMA Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Figure 86. E Clock Timing (BUS RELEASE Mode, SLEEP Mode, and
SYSTEM STOP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Figure 87. E Clock Timing (Minimum Timing Example of PWEL and
PWEH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Figure 88. Timer Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Figure 89. SLP Execution Cycle Timing Diagram . . . . . . . . . . . . . . 203
Figure 90. CSI/O Receive/Transmit Timing Diagram . . . . . . . . . . . 204
Figure 91. External Clock Rise Time and Fall Time . . . . . . . . . . . . 204
(Except EXTAL, RESET) . . . . . . . . . . . . . . . . . . . . . . . . 204
Figure 93. Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
UM005004-0918
Advertisement
Table of Contents
Need help?
Do you have a question about the Z8018 Series and is the answer not in the manual?
Questions and answers
are there a timing diagrams for PUSH and POP instructions?
The timing diagrams for the PUSH and POP instructions for the ZiLOG Z8018 Series are as follows:
POP Instruction (e.g., POP IX or POP IY):
- Machine Cycle 1 (MC1): Fetch POP opcode.
- Machine Cycle 2 (MC2): Fetch address code.
- Machine Cycle 3 (MC3): Read from memory at SP (Stack Pointer); data goes to low byte (e.g., IXL or IYL).
- Machine Cycle 4 (MC4): Read from memory at SP+1; data goes to high byte (e.g., IXH or IYH).
PUSH Instruction (e.g., PUSH IX or PUSH IY):
- Machine Cycle 1 (MC1): Fetch PUSH opcode.
- Machine Cycle 2 (MC2): Fetch address code.
- Machine Cycle 3 (MC3): Decrement SP by 1 and write high byte (e.g., IXH or IYH) to memory at SP.
- Machine Cycle 4 (MC4): Decrement SP by 1 and write low byte (e.g., IXL or IYL) to memory at SP.
Each machine cycle includes three T-states (T1, T2, T3), and memory control signals (such as MREQ, RD, WR) are active as needed during these cycles.
This answer is automatically generated