Kenwood NX-5000 Series Common Function Reference page 66

3 BASIC OPERATIONS
3.3 Using Function Keys
Configuration
NXDN Conventional system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Group Call Mode in an
NXDN Conventional system. In Group Call Mode, a call can be initiated by selecting a Group ID
registered in the Group ID List. Then, pressing the [F] key while the transceiver is in Group Call
Mode allows the transceiver to enter Short Message Mode. In Short Message Mode, a Short
Message can be sent by directly entering a Short Message.
NXDN Trunking system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Short Message Mode in
an NXDN Trunking system. In Short Message Mode, a Short Message can be sent by directly
entering a Short Message.
Group + Short
Message
P25 Conventional system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Talkgroup ID Select
Mode in a P25 Conventional system. In Talkgroup ID Select Mode, the Talkgroup ID configured
for a channel can be changed.
DMR Conventional system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Group Call Mode in a
DMR Conventional system. In Group Call Mode, a Group Call can be initiated by selecting a Group
ID registered in the Group ID List. Then, pressing the [F] key while the transceiver is in Group
Call Mode allows the transceiver to enter Short Message Mode. In Short Message Mode, a Short
Message can be sent by directly entering a Short Message.
NXDN Conventional system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Group Call Mode in an
NXDN Conventional system. In Group Call Mode, a call can be initiated by selecting a Group ID
registered in the Group ID List. Then, pressing the [F] key while the transceiver is in Group Call
Mode allows the transceiver to enter Status Mode. In Status Mode, a Status Message can be sent
by selecting a status configured in NXDN Status List or directly entering a status number.
NXDN Trunking system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Status Mode in an NXDN
Trunking system. In Status Mode, a Status Message can be sent by selecting a status configured
in NXDN Status List or directly entering a status number.
Group + Status
P25 Conventional system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Talkgroup ID Select
Mode in a P25 Conventional system. In Talkgroup ID Select Mode, the Talkgroup ID configured
for a channel can be changed.
DMR Conventional system:
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Group Call Mode in a
DMR Conventional system. In Group Call Mode, a Group Call can be initiated by selecting a Group
ID registered in the Group ID List. Then, pressing the [F] key while the transceiver is in Group
Call Mode allows the transceiver to enter Status Mode. In Status Mode, a status can be sent by
selecting a status configured in the DMR Status List or directly entering a status.
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Direct Channel & OST
Mode. If the Menu ([Q]) or the [*] key is pressed in Direct Channel & OST Mode, the transceiver
Direct Channel &
migrates to the channel of the entered number. Or, if the Back ([O]) or [#] key is pressed in Direct
OST
Channel & OST Mode, the transceiver migrates to the OST list of the entered number, and this OST
list number is configured after the OST list number is displayed for 2 sec.
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Free-dial Entry Mode. In
Free-dial Entry
Free-dial Entry Mode, a 5-tone code can be sent by directly entering a 5-tone code.
Note
Refer to each Function Reference for details about various calls.
0
To directly enter an Individual ID or status in an NXDN system, P25 system, or DMR Conventional system, Manual Dialing
0
needs to be enabled using KPG-D1/ D1N. (Refer to
Refer to "Available Functions for the PF
0
Configuration using KPG-D1/ D1N
Configuring Keypad Operation (
Common FUNC (K, F)/Ver 2.20
Description
Manual Dialing.)
Keys" for the description on FleetSync or MDC-1200.
Transceiver Settings > Key Assignment > General > Keypad)
CONTENTS INDEX
35