Kenwood NX-5000 Series Common Function Reference page 64

3 BASIC OPERATIONS
3.3 Using Function Keys
Keypad Operation
The keypad operating method can be selected according to the user's purpose.
Functions can be assigned to the keypad by using KPG-D1/ D1N. The following is the list of the functions that can be
assigned to the transceiver for Keypad Operation:
Configuration
Pressing a key on the keypad of the transceiver causes the Key-entry Error Tone (1 beep) to sound,
None
but it has no effect on the transceiver.
Pressing a key on the keypad can directly specify a channel. (Refer to
Channel Entry
Specifying the Number (Channel
In an NXDN Trunking system, pressing the [0] to [9] keys on the transceiver's keypad can directly
specify the Group ID in the NXDN Trunking system. (Refer to
the ID (Group ID Entry) (NXDN Trunking System
Group ID/Channel
Entry
In a system other than an NXDN Trunking system, pressing the [0] to [9] keys on the transceiver's
keypad can directly specify the channel number. (Refer to
Number (Channel
Pressing a key on the keypad can directly select the OST from the OST List 1 to OST List 40. (Refer
OST
to Analog FUNC
In a P25 Trunking system, NXDN Trunking system, NXDN Conventional system, DMR Conventional
system, or Analog Conventional system, pressing the [0] to [9] keys on the keypad allows the
transceiver to enter Autodial Mode. In Autodial Mode, the transceiver can transmit by selecting a
DTMF code from Autodial List or directly entering a DTMF code.
However, the transceiver behavior on a control channel varies as below depending on the
configuration in Telephone Interconnect (List Only, Unlimited or Answer Only). (Refer to P25 FUNC
Configuring the Transmission and Reception Behaviors of a Telephone Call (Telephone
Interconnect).)
Answer Only:
The transceiver cannot enter Autodial Mode on a control channel.
Unlimited:
Autodial
If the transceiver enters Autodial Mode on a control channel, the transceiver can transmit by
selecting a DTMF code from the Autodial List when Autodial List is configured. If Autodial List
is not configured, the transceiver can transmit by directly entering a DTMF code.
List Only:
If the transceiver enters Autodial Mode on a control channel, the transceiver can transmit by
selecting a DTMF code from the Autodial List when Autodial List is configured. If Autodial List
is not configured, the transceiver cannot transmit a DTMF code.
If Store & Send is disabled and Autodial List is configured, transmission of a DTMF code on a
communication channel, regardless of the configuration in Telephone Interconnect, allows the
transceiver to transmit by selecting a DTMF code from Autodial List. If Store & Send is enabled,
the transceiver can transmit by directly entering a DTMF code.
Keypad Auto PTT Every time a key on the keypad is pressed, the DTMF code is instantly sent.
Pressing the [0] to [9] keys on the keypad enters Short Message Mode. In Short Message Mode, a
Short Message
Short Message can be sent by directly entering a Short Message.
Pressing the [0] to [9] keys on the keypad enters Status Mode. In Status Mode, a status configured
in the Status List in a P25 Trunking system, an NXDN system, or a DMR Conventional system can
Status
be selected. Also, in an NXDN system, a Status Message can be sent by directly entering a status
number.
Pressing the [0] to [9] keys on the keypad allows the transceiver to enter Individual Call Mode in a
P25 system, NXDN system, or DMR Conventional system. In Individual Call Mode, a call can be
Individual
initiated by selecting an Individual ID configured in the Individual ID List or directly entering an
Individual ID.
Common FUNC (K, F)/Ver 2.20
Table 3-4 Keypad Operation
Description
Entry).)
Entry).)
Changing the Decode/ Encode Combination of the QT/ DQT
Changing the Channel by
Changing the Group ID by Specifying
Only).)
Changing the Channel by Specifying the
CONTENTS
(OST).)
33
INDEX