Table of Contents
Advertisement
6.3.5 NVM 740_IOT Manager List
Chain-Link NVM Name
740-002
Cycle Down Timer for Sheet Empty
740-006
PAR Receive Timeout Error
740-007
PAR Receive Sequence Bit Error
740-008
PAR Receive Check Sum Error
740-009
PAR Send Error
740-028
ACS Wait Timer
740-029
ACS BW Plate Count
740-030
ACS Sheet Read Count
740-033
Normal Smear Countermeasure Switch
740-034
Heavyweight1 Type Smear Countermeasure
Switch
740-035
HW Heavyweight Type Smear Countermea-
sure Switch
740-036
Gloss1 Type Smear Countermeasure
Switch
740-037
HW Gloss Type Smear Countermeasure
Switch
740-038
Access Detector Selection Switch
740-042
Diagnostic Device Data Send Cycle
740-061
EEPROM Information
740-109
Productivity Modification Switch (Heavy-
weight Smear Countermeasure)* This is
valid only for 25-sheet and 35-sheet models.
740-110
Custom Toner Mode Switch History
Version 1.1
DC SC2020
Table 1 NVM 740_IOT Manager List
Default
Minimum
Maximum
Value
value
value
Description
7000
0
20000
Cycle down timer for Sheet Empty.
Timer for starting Cycle Down after the machine becomes the Sheet Empty status while
printing.
When Cycle Down starts at abnormal failure or when a stop instruction is issued, Cycle
Down starts immediately without using this timer.
0
0
255
No. of Sending Timeouts
0
0
255
No. of Sequence Bit errors
0
0
255
No. of Check Sum errors
0
0
255
No. of IOT Resends
20
0
255
The maximum activation wait time until a color mode is determined when the ACS stan-
dard switching mode is set.
5
3
255
The B/W Continuous Sheets Threshold Value, which is used to judge if the machine
has switched to the B/W mode when the ACS standard switching mode is set.
3
0
255
The number of look-ahead sheets, which is used to judge if the machine has switched
to the B/W mode when the ACS standard switching mode is set.
0
0
1
Operate in FC Mode without following the instruction from the Controller.
0: OFF, 1: ON
0
0
1
Operate in FC Mode without following the instruction from the Controller.
0: OFF, 1: ON
0
0
1
Operate in FC Mode without following the instruction from the Controller.
0: OFF, 1: ON
0
0
1
Operate in FC Mode without following the instruction from the Controller.
0: OFF, 1: ON
0
0
1
Operate in FC Mode without following the instruction from the Controller.
0: OFF, 1: ON
0
0
1
Select Execute/Do not execute the Access Detector.
0: Perform (Accept the SC Prestart Marking from the Controller.)
1: Do not perform (Ignore the SC Prestart Marking from the Controller.)
0
0
12
Send cycle for diagnostic device usage status (Local)
1-12: Send Cycle Time (TIme)
0: Do not send
0
0
2
2: High, 1: Mid, 0: Low
0
0
1
Change the productivity with Heavyweight Smear Countermeasure.
0: OFF (Do not perform), 1: ON (Perform)
0
0
1
Custom Toner Mode Entry History
05/2014
6-39
Write
Allowed/
Can be
Unit
Protected
initialized
1 [ms]
O
O
-
O
O
-
O
O
-
O
O
-
O
O
100 [ms] O
O
Side
O
O
Sheet
O
O
-
O
X
-
O
X
-
O
X
-
O
X
-
O
X
-
O
X
-
O
O
-
X
X
-
O
X
-
O
X
6.3.5 NVM 740_IOT Manager List
General
Advertisement
Chapters
Table of Contents
Troubleshooting
