Toner Y Crum Data Mismatch; Toner M Crum Data Mismatch; Toner C Crum Data Mismatch; Toner Y Crum Not In Position - Fuji Xerox DocuCentre SC2020 Service Manual

093-960 Toner Y CRUM Data Mismatch

BSD-ON:CH9.5
Detected invalid Authentication Area Data of CRUM of Toner Cartridge (Y).
Cause/Action
Remove and reinstall the Toner Cartridge (Y) and check for improper installation.
Replace with genuine Toner Cartridge (Y) (PL

093-961 Toner M CRUM Data Mismatch

BSD-ON:CH9.5
Detected invalid Authentication Area Data of CRUM of Toner Cartridge (M).
Cause/Action
Remove and reinstall the Toner Cartridge (M) and check for improper installation.
Replace with genuine Toner Cartridge (M) (PL

093-962 Toner C CRUM Data Mismatch

BSD-ON:CH9.6
Detected invalid Authentication Area Data of CRUM of Toner Cartridge (C).
Cause/Action
Remove and reinstall the Toner Cartridge (C) and check for improper installation.
Replace with genuine Toner Cartridge (C) (PL

093-970 Toner Y CRUM Not In Position

BSD-ON:CH9.5
CRUM of Toner Cartridge (Y) is not installed in the predetermined position (CRUM falling out).
Cause/Action
1.Remove and reinstall the Toner Cartridge (Y).
Version 1.1
DC SC2020
5.1) if there is no problem after checking.
5.1) if there is no problem after checking.
5.1) if there is no problem after checking.
2.Wipe the joining terminal between CRUM PWB of Toner Cartridge (Y) and CRUM of Toner CRUM
Connector Assembly (Y) with a dry cloth. (When cleaning, do not use Drum cleaner, etc.)
3.Check the following:
• Disconnection, shortage or contact failure of wire between DRIVE PWB
CRUM Connector Assembly (Y) J101.
• Damage, contamination by foreign substances of the joining terminal between CRUM PWB of
Toner Cartridge (Y) and CRUM of Toner CRUM Connector Assembly (Y).
• The Toner Cartridge (Y) for improper installation
If no problem is found, replace the following parts in sequence:
• Toner Cartridge (Y) (PL 5.1)
• Toner CRUM Connector Assembly (Y) (Dispenser Drive (YM))
• DRIVE PWB (PL 18.2)

093-971 Toner M CRUM Not In Position

BSD-ON:CH9.5
CRUM of Toner Cartridge (M) is not installed in the predetermined position (CRUM falling out).
Cause/Action
1.Remove and reinstall the Toner Cartridge (M).
2.Wipe the joining terminal between CRUM PWB of Toner Cartridge (M) and CRUM of Toner CRUM
Connector Assembly (M) with a dry cloth. (When cleaning, do not use Drum cleaner, etc.)
3.Check the following:
• Disconnection, shortage or contact failure of wire between DRIVE PWB
CRUM Connector Assembly (M) J102.
• Damage, contamination by foreign substances of the joining terminal between CRUM PWB of
Toner Cartridge (M) and CRUM of Toner CRUM Connector Assembly (M).
• The Toner Cartridge (M) for improper installation
If no problem is found, replace the following parts in sequence:
• Toner Cartridge (M) (PL 5.1)
• Toner CRUM Connector Assembly (M) (Dispenser Drive (YM))
• DRIVE PWB (PL 18.2)

093-972 Toner C CRUM Not In Position

BSD-ON:CH9.6
CRUM of Toner Cartridge (C) is not installed in the predetermined position (CRUM falling out).
Cause/Action
1.Remove and reinstall the Toner Cartridge (C).
05/2014
2-101
J405 and Toner
(PL 5.3)
J405 and Toner
(PL 5.3)
CHAIN 93
Troubleshooting