Fuji Xerox DocuCentre SC2020 Service Manual page 599

Table 2 Function Names and Details (Fax/Scanner)
Function Description
Relay/Sig- Relay Toggles the Relay signal at the specified frequency.
nal Test Test
Hook Toggles the Hook signal at the specified frequency.
Test
Single Continuously sends the tone at the selected fre-
Tone quency.
Send
DTMF Continuously sends the DTMF signal.
Send
Dial Sends the multi-digits Dial Pulse (10/20pps) signal.
Pulse
Send
Ring Sends the ringback tone.
Back
Tone
Data Specifies the speed and pattern for checking data
Send forwarding(no pattern for V.34)
Line Volt- Checks the status of the Line Voltage.
age
Line Cur- Checks the status of the Line Current.
rent
Information Scan Counter Displays the Scan counter value.
Scanner Scan Counter Clears the number of times were scanned using the
Maintenance Counter Clear Platen.
Clear (FB)
Counter Clears the number of times were scanned using the
DADF.
Clear
(DADF)
Auto Shad- (Ready to (Platen) Performs auto correction for the White Ref-
ing Start) erence Board's uneven density and degradation due
to the passage of time.
CVT Auto (Ready to This diagnostic function performs correction on the
Shading Start) density dispersion that is caused by floating DADF.
(Color) Scans in Color and calculates the Color Density
Coefficient.
CVT Auto (Ready to This diagnostic function performs correction on the
Shading Start) density dispersion that is caused by floating DADF.
(Gray) Scans in Gray and calculates the Gray Density Coef-
ficient.
Version 1.1
DC SC2020
Table 2 Function Names and Details (Fax/Scanner)
See Function
6.4.14.5 LED Cali-
bration
6.4.14.5
6.4.14.5
Componet
Check
6.4.14.5
DADF
6.4.14.5
Componet
Check
6.4.14.5
DADF Size
Detect
6.4.14.5
Auto Adj.
Parameter Chain Link
6.4.14.5
BackupData All Clear
6.4.14.5 User Clear
Sysytem Clear
6.4.15.1
User&Sysytem Clear
6.4.16.1
System Data Init
Document Clear
DADF Clear
6.4.16.1
Complete Complete
6.4.16.2
6.4.16.3
6.4.16.4
05/2014
6-201
Description
(Ready to Performs correction on the dispersion that is caused
Start) by the LED lamp color sensitivity. Calculates a* and
b* from the Y Patch scan value of Calibration Chart
(STP5001) and then compares them with reference
values that were pre-set in the NVM to select the
Correction Coefficient No. to set in the NVM.
IIT Input Digital Input Checks the status of the IIT sensor.
IIT Output Digital Output Checks the status of the motor drive.
DADF IIT Digital Input Checks the status of the DADF sensor.
Input
DADF IIT Digital Output Checks the status of the motor drive.
Output
(Ready to Performs troubleshooting for the IIT and displays the
Start) presumed Faulty Parts No. on the UI.
Specifies the system data setting using ChainLink.
Deletes the SRAM/EEPROM backup data.
Deletes the SRAM/EEPROM backup data.
Deletes the SRAM/EEPROM backup data.
Deletes the SRAM/EEPROM backup data.
Deletes the SRAM/EEPROM backup data.
Deletes the document data in the Fax Flash Memory.
Deletes the DADF data .
Exits the CE mode and restarts the MPF.
6.4.6 CE Mode Functions Overview
See
6.4.16.5
6.4.16.6
6.4.16.6
6.4.16.7
6.4.16.7
6.4.16.8
6.4.17
6.4.18
6.4.18
6.4.18
6.4.18
6.4.18
6.4.18
6.4.18
6.4.4
General