Adj 8.1.5 Procon/Regcon Print - Fuji Xerox DocuCentre SC2020 Service Manual

Corresponding PG and operation of Test Pattern
Print
Table 1 Corresponding PG and operation of Test Pattern Print
Test
Pattern
Print
Name Y M C
Y Up A4 HT10% HT10% HT10%
5PV Image A4 Image A4 Image A4
5 copies 5 copies 5 copies
(Disp More) (Disp Less) (Disp Less)
M Up A4 HT10% HT10% HT10%
5PV Image A4 Image A4 Image A4
5 copies 5 copies 5 copies
(Disp Less) (Disp More) (Disp Less)
C Up A4 HT10% HT10% HT10%
5PV Image A4 Image A4 Image A4
5 copies 5 copies 5 copies
(Disp Less) (Disp Less) (Disp More)
K Up A4 HT10% HT10% HT10%
5PV Image A4 Image A4 Image A4
5 copies 5 copies 5 copies
(Disp Less) (Disp Less) (Disp Less)
Y Down A4 HT70% HT10% HT10%
10PV Image A4 Image A4 Image A4
10 copies 10 copies 10 copies
(without (Disp Less) (Disp Less)
Disp)
M Down A4 HT10% HT70% HT10%
10PV Image A4 Image A4 Image A4
10 copies 10 copies 10 copies
(Disp Less) (without (Disp Less)
Disp)
C Down A4 HT10% HT10% HT70%
10PV Image A4 Image A4 Image A4
10 copies 10 copies 10 copies
(Disp Less) (Disp Less) (without
Disp)
K Down A4 HT10% HT10% HT10%
10PV Image A4 Image A4 Image A4
10 copies 10 copies 10 copies
(Disp Less) (Disp Less) (Disp Less)
Note
• Fusing Unit will not operate until it is "Ready". In addition, it
Version 1.1
DC SC2020
does not perform billing up.
• For XERO/DEVE, this is the same as the case for normal oper-
ations.
• If the [Stop] button is pressed during ToneUp/Down, the
ToneUp/Down operation will be stopped and you will return to
the initial screen.
K
HT10%
Image A4
5 copies
(Disp Less)
HT10%
Image A4
5 copies
(Disp Less)
HT10%
ImageA4
5 copies
(Disp Less)
HT10%
Image A4
5 copies
(Disp More)
HT10%
Image A4
10 copies
(Disp Less)
HT10%
Image A4
10 copies
(Disp Less)
HT10%
Image A4
10 copies
(Disp Less)
HT70%
Image A4
10 copies
(without
Disp)

ADJ 8.1.5 ProCon/RegCon Print

Purpose
•
Execution Period
•
Action
•
05/2014
4-99
Print the decided IOT NVM setting value on the paper.
When performing ProCon/RegCon setting print
Enter the CE DIAG Mode, [Printer Diag] -> [Parameter] ->
[Parameter] -> [Procon Print]
After accepting the execution instruction, print the designated
IOT NVM value.
A: The warning of Process Control, Registration Control is indi-
cated up to the blank like of the first page, so make sure this is
all 0.
Figure 1 j0bs40883
Disassembly/Assembly and Adjustment
8. Xero./Deve.