HP E1313A Manual page 286

Command
:TARE (@<ch_list>)
:RESet
:TARE?
:VALue
:RESistance <ref_ohms>
:VOLTage <ref_volts>
:ZERO?
DIAGnostic
:CALibration
:TARE
[:OTDetect]
[:MODE]
[:MODE]?
:CHECksum?
:COMMand
:SCPWRITE <reg_addr>,<reg_data>
:CUSTom
:LINear <table_ad_range>,<table_block>,(@<ch_list>)
:PIECewise <table_ad_range>,<table_block>,(@<ch_list>)
:REFerence:TEMPerature
:FLOor[:CONFigure] <range>,(@<ch_list>)
:FLOor:DUMP
:INTerrupt[:LINe] <intr_line>
:INTerrupt[:LINe]?
:OTDetect[:STATe] ON | OFF, (@<ch_list>)
:OTDetect[:STATe]? (@<channel>)
:QUERy
:SCPREAD <reg_addr>
:VERSion?
FETCh?
FORMat
[:DATA] <format>[, <size>]
ASCii[, 7]
PACKed[, 64]
REAL[, 32]
REAL, 64
[:DATA]?
INITiate
:CONTinuous ON | OFF
[:IMMediate]
INPut
:FILTer
[:LPASs]
:FREQuency <cutoff_freq<D>,(@<ch_list>)
:FREQuency? (@<channel>)
[:STATe] ON | OFF, (@<channel>)
[:STATe]? (@<channel>)
:GAIN <chan_gain>,(@<ch_list>)
:GAIN? (@<channel>)
Chapter 5
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
SCPI Command Quick Reference
Calibrate out system field wiring offsets.
Resets cal constants from CALibration:TARE back to zero for all
channels.
Returns state of CALibration:TARE operation (returns error codes or 0
for OK).
Send to instrument the value of just measured reference resistor.
Send to instrument the value of just measured voltage reference.
Correct A/D for short term offset drift (returns error codes or 0 for OK).
Sets mode to control OTD current during tare calibration.
Returns current setting of OTD control during tare calibration.
Perform checksum on Flash RAM and return a '1' for OK, a '0' for
corrupted or deleted memory contents.
Writes values to SCP registers.
Loads linear custom EU table.
Loads piecewise custom EU table.
Puts the contents of the Reference Temperature Register into the FIFO.
Sets lowest range that autorange can select.
Sends the autorange floor setting for all 64 channels to the FIFO.
Sets the VXIbus interrupt line the module will use.
Returns the VXIbus interrupt line the module is using.
Controls " Open Transducer Detect" on SCPs contained in <ch_list>.
Returns current state of OTD on SCP containing <channel>.
Returns value from an SCP register.
Returns manufacturer, model, serial#, flash revision #, and date
e.g. HEWLETT-PACKARD,E1413C,US34000478,A.04.00,
Wed Jul 08 11:06:22 MDT 1994
Return readings stored in VME Memory (format set by FORMat:DATA
cmd).
Set format for response data from [SENSe:]DATA?.
Seven bit ASCII format (not as fast as 32-bit because of conversion).
Same as REAL, 64 except NaN, +INF, and -INF format compatible
with HP BASIC.
IEEE 32-bit floating point (requires no conversion so is fastest).
IEEE 64-bit floating point (not as fast as 32-bit because of conversion).
Returns format: REAL, +32 | REAL, +64 | PACK, +64 | ASC, +7.
When ON, module returns to Waiting for Trigger state after each scan.
When OFF, module goes to Trigger Idle state after each scan.
Put module in Wait-for-Trigger state (ready to make one scan).
Control filter Signal Conditioning Plug-ons.
Sets the cutoff frequency for active filter SCPs.
Returns the cutoff frequency for the channel specified.
Turn filtering OFF (pass through) or ON (filter).
Return state of SCP filters.
Set gain for amplifier-per-channel SCP.
Returns the channel's gain setting.
HP E1313/E1413 Command Reference
Command Quick Reference
Description
285