Xerox WorkCentre 5687 Series Service Manual page 1961

Table 6 NVM chain 7
Location NVM Name NVM Description
07-010 LE Late T2 Feed Maximum number of steps
Snr from tray 2 feed motor to LE
at tray 2 feed sensor.
07-011 T1 Buckle Size Number of steps from LE at
tray 1 feed sensor to start of
transport motor.
07-012 T2 Buckle Size Number of steps from LE at
tray 2 feed sensor to start of
tray 1 and 2 transport motor.
07-013 LE Late T1 From T2 Maximum number of steps
from tray 2 TAR nips to LE at
tray 1 feed sensor.
07-014 LE Late Wait Point Maximum number of steps
T1-T2 from tray 1 TAR nips to LE at
wait sensor.
07-015 Wait Point Steps T1- Number of steps from LE at
T4 wait sensor to tray 1 and 2
transport motor stop.
07-016 Release Steps T1- Number of steps the tray 1
T4 and 2 transport motor should
run after the release sheet
command.
07-017 LE Late T2 From Time for the LE of an HCF
T3-T4 sheet to reach the tray 2 feed
sensor.
07-018 Release Steps T5 Distance from wait point to
transport motor releasing
sheet.
07-019 T3 Stack Height Number of steps tray 3 has to
Adjust be lifted above the stack
height sensor for optimum
feed position.
07-020 T4 Stack Height Number of steps tray 4 has to
Adjust be lifted above the stack
height sensor for optimum
feed position.
07-021 LE Late T3 Feed Maximum number of steps
Snr from tray 3 feed motor to LE
at tray 3 feed sensor.
07-022 LE Late T4 Feed Maximum number of steps
Snr from tray 4 feed motor to LE
at tray 4 feed sensor.
07-023 T3 Buckle Size Size of de-skew buckle.
07-024 T4 Buckle Size Size of de-skew buckle.
WorkCentre 5687 Family
Value Default Location NVM Name
0 to 500 200 07-025
0 to 200 13
07-026
0 to 200 13
07-027
0 to 1200 940
07-028
0 to 1400 1000 07-029
0 to 600 32/38/45/
55=240
65/75/87
=434
Location NVM Name
0 to 2000 440
08-001
0 to 2000 1400
0 to 1000 116
08-002
0 to 100 50
08-003
0 to 100 50
08-004
08-045
0 to 700 350
08-046
0 to 800 400
08-047
0 to 15 3
08-048
0 to 15 10
August 2007
6-69
Table 6 NVM chain 7
NVM Description
Release Steps T3- Number of steps the HCF
T4 transport motor should run
after the release sheet com-
mand.
LE Late T4 From T3 Maximum number of steps
from tray 3 TAR nips to LE at
tray 4 feed sensor.
Wait Point Steps T3- Number of steps from tray 4
T4 feed sensor to stop position.
PreRelease Dis- Number of steps for pre-
tance T1 sheet separation.
Tray Media Combi Tray media size sensing
Switch switch to alternate between
old and new switch combina-
tions.
Table 7 NVM chain 8
NVM Description
Print Rate Number of prints per minute
(Controls the IOT print rate).
03-012 must be set to the
same speed.
Process speed Speed at which sheets
move through machine.
Machine Model Machine configuration set-
ting.
Machine Type Machine type setting.
Short Cycle Out IOT inactivity shutdown
Time timer (except ROS motor).
Long Cycle Out Inactivity cycle out timer.
Time
Abnormal Cycle Abnormal cycle out time.
Out Time
Top Edge Reg Tray Tray 1 top edge registration
1 Simp simplex.
Value Default
0 to 15 5
0 to 2000 1000
30 to 100 32/38/45/
55=40
65/75/87 =53
100 to 150 130
0=Old combi- 1
nation
1=New com-
bination
Value Default
0=38 ppm, 7
1=45 ppm,
2=55 ppm,
3=65 ppm,
4=75 ppm,
5=32 ppm,
6=87 ppm,
7=Unknown
speed
160 to 500 32/38=179
45/55=257
65/75/87=362
6 0
0=Unknown 0
1=Universal
0 to 15 seconds 0
0 to 180 sec- 32/38/45=0
onds 55/65/75/87
=60
0 to 15 seconds 32/38/45=0
55/65/75/87
=10
7300 to 7700 7510
General Procedures & Information
dC131a