Xerox WorkCentre 5687 Series Service Manual page 2201

Table 4 Input codes 07
Code Displayed Name Description
07-337 T2 stack height Sensor Tray 2 stack height sensor (Q07-
337)
07-338 T3 Level Encoder Detects tray 3 paper level encoder
status (Q07-338)
07-339 T4 Level Encoder Detects tray 4 paper level encoder
status (Q07-339)
07-341 T1 paper low switch Detects if the stack height of tray 1
is more than 25% (S07-341)
07-342 T2 paper low switch Detects if the stack height of tray 2
is more than 25% (S07-342)
07-350 Bypass Width Sensor Bypass width sensor (Q07-335)
07-372 T5 Docking Switch Detects that tray 5 is in the docked
position (S07-372)
07-383 T3 Stack Height Sen- Tray 3 stack height sensor (Q07-
sor 383)
07-384 T4 Stack Height Sen- Tray 4 stack height sensor (Q07-
sor 384)
07-385 T3 hall Sensor Tray 3 hall sensor (Q07-385)
The sensor is located on a small
PCB and detects magnetic field
changes as the feed motor rotates.
07-386 T4 hall Sensor Tray 4 hall sensor (Q07-386)
The sensor is located on a small
PCB and detects magnetic field
changes as the feed motor rotates.
07-387 HCF 24V Monitor Indicates the state of 24V input
monitor
07-401 T5 Tray Empty Sensor Detects the presents of paper on
tray 5 (Q07-401)
07-402 T5 Stack Height Sen- Tray 5 stack height sensor (Q07-
sor 402)
07-403 T5 24V Monitor Indicates the state of 24V input
monitor
07-405 T5 Stack Down Sensor Tray 5 stack down sensor (Q07-
405), detects when the tray is in the
fully lowered position
WorkCentre 5687 Family
General Code Displayed Name
High = top of stack 07-406 T5 El Motor Encoder
sensed, low = top of Sensor
stack not sensed
High = top of stack
sensed, low = top of
Code Displayed Name
stack not sensed
08-100 Wait Sensor
High = top of stack
sensed, low = top of
stack not sensed
08-101 T1 Feed Sensor
High = more than 25%
full, Low = less than
08-102 T2 Feed Sensor
25% full
High = more than 25%
08-103 T3 Feed Sensor
full, Low = less than
25% full
08-104 T4 Feed Sensor
Display indicates width
setting 100 to 300 mm
(3.93 to 11.81 inch) 08-105 T5 Feed Sensor
High = Tray 5 docked
08-110 T5 wait Point Sensor
High = top of stack
sensed, low = top of
stack not sensed
08-111 T5 Release Sheet Hot-
High = top of stack
line
sensed, low = top of
stack not sensed 08-150 Registration Sensor
High = Made. Only run
when T3 door is open 08-160 Duplex Sensor
High = Made. Only run
when T4 door is open
Code Displayed Name
09-060 HVPS Fault
09-070 Scorotron cleaner
High = 24V present
home sensor
High = paper present,
09-073 Transfer / Detack
Low = no paper
Home Sensor
High = top of stack
sensed, Low = top of
stack not sensed
High = 24V present
High = tray is fully down
August 2007
6-309
Table 4 Input codes 07
Description General
Encoder sensor (Q07-406), detects High = detected, low =
state of motor encoder sensor bit not detected
Table 5 Input codes 08
Description General
Wait sensor (Q08-100), detects High = paper present,
when lead edge of paper at wait low = no paper
point.
Detects when lead edge of paper is High = paper present,
at tray 1 feed sensor, (Q08-101) low = no paper
Detects when lead edge of paper is High = paper present,
at tray 2 feed sensor, (Q08-102) low= no paper
Detects when lead edge of paper is High = paper present,
at tray 3 feed sensor, (Q08-103) low = no paper
Detects when lead edge of paper is High = paper present,
at tray 4 feed sensor, (Q08-104) low = no paper
Detects when the lead edge of the High = paper present,
paper is at tray 5 feed sensor (Q08- Low = no paper
105)
Wait sensor (Q08-110), detects High = paper present,
when lead edge of paper at wait low = no paper
point. (same sensor as for 08-100)
Displays the state of the release High = hotline active,
sheet hotline low = not active
Detects when paper is at the regis- High = paper present,
tration sensor (Q08-150) low = no paper
Detects when paper is at the duplex High = paper present,
sensor (Q08-160) low = no paper
Table 6 Input codes 09
Description General
Detects a fault in the HVPS High = fault, low = good
Detects the scorotron cleaning High = head not home,
head in the home position low = head in home
position
Transfer / detack cleaner head High = head not home,
home sensor. Low = head in home
position
Stack with transfer /
detack corotron cleaner
motor stall sensor,
motor forward and
motor reverse
General Procedures & Information
dC330