Xerox WorkCentre 5687 Series Service Manual page 2194

Table 6 Jordan NVM values
Location NVM Name NVM Description
20-909 FaxIntDtnNum- Int Dtone number cell pat-
CellPatt tern
20-911 FaxIntDtoneMak Int Dtone make min 1
eMin1
20-912 FaxIntDtoneMak Int Dtone make max 1
eMax1
20-913 FaxIntDtoneMak Int Dtone make hole 1
Hole1
20-914 FaxIntDtoneBrek Int Dtone 1 break min 1
Min1
20-915 FaxIntDtoneBrek Int Dtone break max 1
Max1
20-917 FaxIntDtoneIdxN Int Dtone idx next cell 1
xtC1
20-919 FaxIntDtFlgDtPe Int Dtone flag detection per-
rfd1 formed 1
20-920 FaxIntDtoneMak Int Dtone make min 2
eMin2
20-921 FaxIntDtoneMak Int Dtone make max 2
eMax2
20-922 FaxIntDtoneMak Int Dtone make hole 2
eHole2
20-923 FaxIntDtoneBrk Int Dtone break min 2
Min2
20-924 FaxIntDtoneBrk Int Dtone break max 2
Max2
20-928 FaxIntDtFlgDetP Int Dtone flag detection per-
rfd2 formed 2
General Procedures & Information
dC131i, dC132
dC132 NVM Initialization
Value Default
There are 4 items under this heading:
Range = 0 to 3 2
•
•
Range = 0 to 10000 ms 130
•
•
Range = 0 to 10000 ms 270
NOTE: Certain NVM settings are password protected.
Range = 0 to 10000 ms 0
Copier NVM Initialization
Purpose
Range = 0 to 10000 ms 130
The NVM initialization routine provides the means for the CSE to reset specific machine vari-
able NVM or all machine variable NVM non-volatile memory (with the exception of Protected
Range = 0 to 10000 ms 270
NVM for which a password is required) to their default values.
Index of next pattern 1
Description
Range = 0 to 255
If the machine configuration changes through the addition of an input or output device, an ini-
Range = 0 to 1 0
tialization of the NVM for that device must be performed to make sure that all configuration val-
ues are correct for that device.
Range = 0 to 10000 ms 490
NOTE: initialization does not affect the billing counter, accounting, fault counter, diagnostic
Range = 0 to 10000 ms 710
data, or auditron services. These, with the exception of billing counters, can be reset if the
machine is restored to the install state using the NVM to Install Condition procedure.
Range = 0 to 10000 ms 40
NOTE: The auditron (billing counters) is initialized using the auditron setup routine, refer to the
User Guide.
Range = 0 to 10000 ms 850
The market region configuration attribute must have been preset at the factory or at first install
to ensure that the NVM default values are regionally correct. Some post install configuration
Range = 0 to 10000 ms 1150
can be performed using the configuration tool, refer to dC131 NVM Read / Write.
Is this the last detection 1
Procedure
pattern?
1.
Range 0 to 1
2.
3.
4.
5.
6.
Network Controller NVM initialization
Purpose
To return to default network settings, configuration and flags.
August 2007
6-302
Copier NVM Initialization
Network Controller NVM initialization
Embedded Fax NVM initialization
NVM to Install Condition
Save the NVM to disk, GP 5.
Enter diagnostics, GP 1.
Select Diagnostic Routines.
Select Copier Routines, 132 NVM initialization-Copier.
Touch the appropriate button to select the NVM to be initialized and follow the on screen
instructions. Refer to Table 1, for the functions that are reset to default.
• All Copier NVM.
• Machine Variable NVM, (i.e. paper path, platen and DADH registration).
• SA / KO Dust Off.
• System Counters Dust Off
NOTE: The NVM window will gray out while the initialization is in progress.
Switch off the machine, then switch on the machine, GP 14.
WorkCentre 5687 Family