Xerox WorkCentre 5687 Series Service Manual page 2207

Table 15 Output codes 08
Code Displayed Name Description
08-010 T1 Feed Motor Energizes the tray 1 feed motor
(MOT 08-010).
08-020 T2 Feed Motor Energizes the tray 2 feed motor.
(MOT08-020)
08-025 T1+2 Transport Energizes the tray 1 and 2 trans-
Motor port motor (MOT08-025)
08-030 T3 Feed Motor Energizes the tray 3 feed motor
(MOT08-030)
08-040 T4 Feed Motor Energizes the tray 4 feed motor
(MOT08-040)
08-045 T3+4 Transport Energizes the tray 3 and 4 trans-
Motor port motor (MOT08-045)
08-046 T5 Transport Motor Energizes the tray 5 transport
motor (MOT08-046)
08-050 Bypass Feed Sole- Energizes the bypass feed sole-
noid noid (SOL08-050)
08-060 Duplex Motor Slow Energizes the duplex motor at sim-
plex speed.
08-062 Duplex Motor Fast Energizes the duplex motor at
duplex speed.
08-070 Registration Clutch Energizes the registration clutch
(CL08-070)
08-117 T5 Feed Motor Energizes the stepper motor to
drive tray 5 nudger and feed rolls.
(MOT08-117)
Table 16 Output codes 09
Code Displayed Name Description
09-010 P/R Motor Energizes the photoreceptor drive
motor (MOT09-010)
09-022 P/R Erase Lamp Energizes the photoreceptor erase
lamp.
09-030 Ozone Fan Energizes the ozone fan.
WorkCentre 5687 Family
General Code Displayed Name
On/off. Linked to tray 1 09-035 P/R Cooling Fan
home sensor. Paper tray
must be open when motor
09-036 Duplex cooling
energized. 90 seconds time-
fans enable
out
On/off. Linked to tray 2
09-037 Duplex cooling
home sensor. Paper tray
fans speed
must be open when motor
09-040 Dispense Motor
energized. 90 seconds time-
out
09-045 Cartridge Motor
On/off. 90 seconds timeout
09-061 Charge Scorotron
On/off. Linked to tray 3
home sensor. Paper tray
must be open when motor
energized. 90 seconds time-
09-062 Charge Grid
out
On/off. Linked to tray 4
home sensor. Paper tray
09-063 Transfer Corotron
must be open when motor
energized. 90 seconds time-
out
09-064 Detack Corotron
On/off. 90 seconds timeout
On/off. 60 seconds timeout
09-065 Chute Bias
On/off. 5 seconds timeout
On/off. 90 seconds timeout
09-066 Dev Bias
On/off. 90 seconds timeout
09-071 Scorotron Cleaner
On/off. 5 seconds timeout
Motor: Forward
On/off. Paper tray must be
09-072 Scorotron Cleaner
down when motor ener-
Motor: Reverse
gized. 60 seconds timeout
09-075 Transfer / Detack
Motor: Forward
General
On/off. 60 seconds timeout
09-076 Transfer / Detack
On/off. 90 seconds timeout
Motor: Reverse
On/off. 90 seconds timeout
August 2007
6-315
Table 16 Output codes 09
Description General
Energizes the photoreceptor fan Full speed/half speed. 90
seconds timeout
Energizes the duplex path cooling On/off. 90 seconds timeout.
fans When enabled the fans will
switch on simultaneously
Duplex path cooling fans: speed On = high speed
0 = low speed
Energizes the toner dispense On/off. 5 seconds timeout
motor (MOT09-040)
Energizes the toner cartridge On/off. 5 seconds timeout
motor (MOT09-045)
Energizes the scorotron wire at On/off. 3 seconds timeout.
nominal drive levels with drives Linked with Charge grid 09-
off. 062. Normally stacked with
HVPS fault
Energizes the grid at nominal drive On/off. 3 seconds timeout.
level with drives off. Linked with charge
scorotron 09-061
Energizes the transfer corotron On/off. 3 seconds timeout.
wire on at nominal drive level with Normally stacked with
drives off. HVPS fault
Energizes the detack wire on. AC On/off. 3 seconds timeout.
voltage and DC current offset at Normally stacked with
nominal drive levels with drives HVPS fault
off.
Energizes the bias voltage on at On/off. 90 seconds timeout.
nominal drive level. Normally stacked with
HVPS fault
Energizes the developer bias volt- On/off. 3 seconds timeout.
age on at nominal drive level with Stack with HVPS fault
drives off.
Energizes the scorotron cleaning On/Off. 13 seconds timeout.
motor (MOT09-070) in the forward Stack with scorotron cleaner
direction home sensor
Energizes the scorotron cleaning On/off. 13 seconds timeout.
motor (MOT09-070) in the reverse Stack with scorotron cleaner
direction home sensor
When set to ON the transfer / On/off. 13 seconds timeout.
detack corotron cleaner motor is Stack with transfer / detack
turned on and run in the forward corotron cleaner motor stall
direction. Moves cleaner to the sensor and motor reverse
rear.
When set to ON the transfer / On/off. 13 seconds timeout.
detack corotron cleaner motor is Stack with transfer / detack
turned on and run in the reverse corotron cleaner motor stall
direction. Moves cleaner to the sensor and motor reverse
front.
General Procedures & Information
dC330